Question about 2000 Jeep Cherokee

2 Answers

Fault codes p1757 p1762 when i doing smoke for dmv when i doing smoke test this code show fault on transmision

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Show us the governor pressure sensor

Posted on Jan 14, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 14,036 Answers

CODE P1757 - GOVERNOR PRESSURE GREATER THAN 3 PSI WHEN REQUESTED TO BE O. CODE P1762 - GOVERNOR PRESSURE SENSOR OFFSET VOLTS TOO LOW OR HIGH.MEANING SENSOR INPUT GREATER OR LESS THAN CALIBRATION FOR 3 CONSECUTIVE NEUTRAL PARK OCCURANCES.

Posted on Sep 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Po1757, po1762


THESE OBD2 CODES ARE TRANSMISSION Trouble codes P1757 & P1762 Governor Pressure Sensor & Solenoid, YOU CAN GET THEM AT MOST PARTS STORES, BUT SOMETIMES THEY CAN BE A BEAR TO CHANGE, TAKE A LOOK AT THEM AT A PARTS STORE & SEE HOW HARD THEY WOULD BE FOR YOU TO REPLACE YOUSELF, IF TOO HARD, YOU MAY HAVE TO GO TO AN ACTUAL TRANSMISSION SHOP FOR THE NEEDED REPAIRS & REPLACEMENT.

Jul 01, 2012 | Dodge Ram 2500 Cars & Trucks

1 Answer

I just got codes p1762, p1757 and p1756 what does this mean


These are all Manufacturer Specific codes which requires that you supply more information about the vehicle to enable proper guidance.

Waiting to help you out.

Oct 04, 2011 | Cars & Trucks

1 Answer

Getting two Codes P1757 and P1762.


P1757--Governor pressure above 3 psi in gear with 0 mph
P1762--Governor pressure sensor offset volts too low or high

Jun 04, 2011 | 2001 Jeep Cherokee

1 Answer

SERIOUS ISSUES HERE. Have a '99 dodge dakota 3.9


we can not fix or suggest a fix for unknown things

Mar 13, 2017 | 1999 Dodge Dakota

1 Answer

Had new battery installed. Plugs wires tried to start turns over just cranks wont start. Checked codes they are p 1757 and p 0441.


image.php?u=60163&dateline=1264699148

o ,Ca75
icon1.gif RE: Transmission Codes P1757 & P1762 Remove the transmission pan and replace the governor pressure solenoid and transducer. There are 3 7/16 or 11mm bolt heads and 2 25mm torque bolts, then remove the bracket holding the sensors up to the valve body. also ajust the bands if needed at that time. __________________

Feb 27, 2011 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

What does codes p1757 an p1762 on 2001 grand cherokee mean


P1757 - Governor Pressure Above 3 PSI When Request Is 0 PSI

P1762 - Governor Pressure Sensor Offset Improper Voltage

Both codes are refered at the governor pressure sensor; I am 99% certain that is bad. Just replace it. Check the voltage on the Light Green/White wire at pin 29 in the white PCM connector with key ON, engine OFF (KOEO). It should be about 0.5-0.7 volts.

If higher than 0.8 volts, check the Transmission Temperature sensor reading on a scan tool. If the Transmission Temperature sensor reads normal, the sensor ground is OK. If the sensor ground is OK, then replace the Governor Pressure sensor.

Hope this helps.

Feb 03, 2011 | 2001 Jeep Cherokee

1 Answer

P1757code p1762 code


P1757 verbiage is "Governor pressure above 3 PSI at 0 MPH". This circuit is continuously monitored with the engine running, not in park or neutral and the MIL not illuminated. The monitor must fail twice to illuminate the MIL. The MIL will illuminate as soon as it fails twice.

If you have any other DTCs set you need to determine their cause first as they could cause this DTC to set. Your idea of deleting the code and driving the vehicle is good because it will ensure that there is a problem, unless it's very intermittent. Based on my experience, this DTC will appear in vehicles that have not had regular transmission filter changes/flushes, in extremely cold weather or some combination of the two.

P1762 - Governor Pressure Sensor (GPS) Offset Volts Too Low Or High. This code will set if the governor pressure is out of range in Park or Neutral for 1.3 seconds. Three consecutive bad 3.0 second tests and sump temperature is greater than 50° F and less than 260° F are required to set the code.
Some of the possible causes are:
  • Transmission fluid level and condition
  • Powertrain Control Module
  • Sensor ground circuit open
  • Intermittent GPS signal
  • 5 volt supply circuit open inside transmission
  • GPS ground circuit open inside transmission
  • Bad GPS
There is little you can do to troubleshoot the system with out a Chrysler DRB scan tool. There are some voltage and resistance tests you can do and I would suggest looking in the Motors Transmission Manual for the proper procedures. You can find the Motors Transmission Manual in the Reference Section of your local Public Libra

Sep 18, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

01 jeep Grand Cherokee transmission problem


Reboot system by disconnecting negative terminal on Battery, with ignition Key on and engine not running, remove terminal for more than two minutes and connect it back, it will spark a little do not panic, and try it again

Feb 01, 2009 | 2001 Jeep Grand Cherokee

1 Answer

2001 jeep grand cherokee transmission revving-codes p1757, p1762


P1757 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Above 3 PSI In Gear At 0 MPH Conditions: Engine started; vehicle driven to a speed over 30 mph, and the PCM detected the Governor Pressure Sensor was more than 3 psi with the requested pressure at 0 psi (95% duty cycle command) for 2.65 seconds. The fault must occur twice on one trip to set the code. Possible Causes: Check for the presence of other A/T related trouble codes Governor pressure Sensor is damaged or has failed Governor pressure Sensor VREF (5v) circuit is open or shorted Transmission valve body is leaking, damaged or has failed PCM has failed P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Nov 17, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Cherokee Logo

938 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...