Question about 2002 Chrysler Sebring

Open Question

ANY TIPS ON CRANKSHAFT PULLEY REMOVAL . I HAVE A 2002 SEBRING - 2.4LTR DOHC ENGINE . I'M REPLACING THE TIMING BELT AND NEED TO REMOVE PULLEY . I'M USING A 4" HEAVY DUTY 3 JAW GEAR PULLER . FITS NICE ON PULLEY BUT AM AFRAID IF I GO ANY TIGHTER I MAY DO DAMAGE TO CRANKSHAFT . IT WON'T BUDGE .

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BCAS1298
  • 3092 Answers

SOURCE: 2002 CHRYSLER SEBRING - 2.4LTR DOHC ENGINE I

There on very tight, did you insert a bolt in the hole, where the bolt for the crank bolt goes on, insert a long where it sticks out pass the pulley about 3 to 4 inches, but thinner bolt in there, and the tip of the puller on it, tighten the puller, and it will come out. I would get two of those bolt's, because it will start to bent, and you might need to used the other bolt to finsh taking it out.

Posted on Sep 01, 2010

Testimonial: "THANK YOU -THANK YOU-THANK YOU !!!! I RECEIVED RESPONSE THIS AM , RIGHT B/4 I WAS TO BEGIN AGAIN AND WITH THIS TIP I HAD THE PULLEY OFF IN 5 MINUTES ."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace timing belt on 2002 kia spectre


Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE
    Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-0.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-3.gif
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

Feb 10, 2016 | 2002 Kia Spectra

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

3 Answers

Timing belt diagram for a 1999 ford escort 2.0


Hope this helps you, you also might want to replace the water pump, due to it's timing belt driven.

29c5183.gif

Sep 24, 2010 | Ford Escort Cars & Trucks

1 Answer

2002 CHRYSLER SEBRING - 2.4LTR DOHC ENGINE I AM INSTALLING NEW TIMING BELT . I AM HAVING TROUBLE REMOVING THE CRANKSHAFT PULLEY . I'M USING A 4" HEAVY DUTY 3 JAW GEAR PULLER AND CAN'T GET THE PULLEY TO...


There on very tight, did you insert a bolt in the hole, where the bolt for the crank bolt goes on, insert a long where it sticks out pass the pulley about 3 to 4 inches, but thinner bolt in there, and the tip of the puller on it, tighten the puller, and it will come out. I would get two of those bolt's, because it will start to bent, and you might need to used the other bolt to finsh taking it out.

Sep 01, 2010 | 2002 Chrysler Sebring

1 Answer

Timing belt broke,engine out of time,need to timing and install new belt how do i set timing.98 escort zx2 2.0 L


2.0L Engine SOHC ENGINE
  1. Remove the drive belt and timing cover.
  2. Raise the car and support it with safety stands.
  3. Remove the right-hand splash shield and the crankshaft pulley. Fig. 11: The timing marks on both the camshaft and crankshaft pulleys must be aligned like this before removing or installing the timing belt — 2.0L SOHC engines 90983g66.gif

  4. Align the timing marks as illustrated in the accompanying illustration.
  5. Refer to the accompanying illustration and remove the timing belt as follows:
    1. Loosen the timing belt tensioner bolt (1).
    2. Use an 8mm Allen wrench, and turn the tensioner (2) counterclockwise 1⁄4 turn.
    3. Insert a 1⁄8 inch drill bit in the hole (3) to lock the belt tensioner in place.
    4. Remove the timing belt (4). Fig. 12: Remove the timing belt by following these 4 numbered steps (refer to the text for an explanation) — 2.0L SOHC engine 90983g67.gif

    5. Inspect the belt for damage and signs of oil leakage. To install: NOTE: Install the timing belt over the sprocket in a counterclockwise direction starting at the crankshaft. Keep the belt span between the crankshaft and camshaft tight when installing the belt over the camshaft.
  6. Install the timing belt and remove the drill bit.
  7. Tighten the tensioner bolt to 15–22 ft. lbs. (20–30 Nm).
  8. Rotate the engine two complete revolutions and make sure the timing marks are aligned.
  9. Install the timing belt cover and crankshaft pulley.
  10. Install the right-hand splash shield and the drive belt.
  11. Start the car and check for proper operation.
DOHC ENGINE NOTE: A camshaft alignment timing tool (No. T94P-6256-CH or equivalent) and a crankshaft Top Dead Center (TDC) timing peg tool (No. T97P-6000-A or equivalent) are required for this procedure. NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block. Refer to the accompanying illustration. Fig. 13: A camshaft alignment timing tool . . . 90983g68.gif
Fig. 14: . . . and a crankshaft TDC timing peg tool are required when removing and installing the timing belt 90983g69.gif
  1. Remove the spark plugs.
  2. Rotate the crankshaft to TDC.
  3. Locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg. Fig. 15: Remove the plug bolt by the Crankshaft Position (CKP) sensor and install the TDC timing peg 90983g70.gif

  4. Raise the car and support it with safety stands.
  5. Unfasten the splash shields bolts and remove the shield.
  6. Lower the car and remove the water pump pulley.
  7. Remove the valve cover and the timing belt covers.
  8. Align the camshafts and install the camshaft alignment tool on the back of the camshafts as illustrated. Fig. 16: Align the camshafts and install the alignment tool 90983g76.gif
    WARNING
    If the camshaft belt is being reused, mark the direction of the camshaft belt to the rotation of the camshaft prior to removal, or premature wear and belt failure could occur.
  9. Loosen the tensioner pulley bolt and relieve the tension on the belt by disconnecting the tensioner tab from the timing cover back plate.
  10. Slide the belt off the sprockets.
  11. Inspect the belt for wear and replace as necessary. Fig. 17: Timing belt routing — 2.0L DOHC engine 90983g71.gif
    To install:
  12. If, for any reason, the engine was disturbed, the camshafts moved or the sprockets replaced, perform the following procedure: NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block.
    1. Position the crankshaft just prior to Top Dead Center (TDC).
    2. If not already done, locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg.
    3. Rotate the crankshaft clockwise against the TDC peg. NOTE: Installation of the alignment tool into the exhaust camshaft may require the camshafts to be rotated clockwise.
    4. Install the camshaft alignment tool on the back of the camshafts.
    5. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
    6. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
    7. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool.
    8. Remove the TDC peg tool and install the plug bolt.
    9. Install the timing and valve covers.
    10. Install the water pump pulley and the splash shield.
    11. Install the spark plugs. If the engine or the camshaft were not disturbed in any way, or the sprockets were not removed, perform the following procedure:
  13. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. Fig. 18: Engage the timing belt tensioner tab into the upper timing cover backplate . . . 90983g72.gif
    Fig. 19: . . . then use a 6mm Allen wrench to adjust the tensioner until the index marks are aligned 90983g73.gif
    Fig. 20: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt (arrow) — 2.0L DOHC engine 90983g75.gif
    NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
  14. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
  15. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool. Fig. 21: Rotate the crankshaft clockwise against the TDC alignment peg 90983g74.gif

  16. Remove the TDC peg tool and install the plug bolt.
  17. Install the timing and valve covers.
  18. Install the water pump pulley and the splash shield.
  19. Install the spark plugs.
prev.gif next.gif

Aug 26, 2010 | Ford E-Series Cars & Trucks

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

2 Answers

Removing Camshaft pulley on 2.5 Dohc forester motor


To replace the timing belt back guard you will have to remove both pulleys.There is a small bolt under each pulley holding the belt guard Use a large socket to hold the pulley while you break the bolt loose with a 17mm socket. I have just done this while replacing my head gaskets due to coolant boiling from the gasket leak.

Dec 15, 2008 | 1998 Subaru Forester

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...