Question about 1991 Toyota Camry

Open Question

Low beams wont work on 1990 camry changed globes checked fuses, changed head lamp relay . switch seems fine , I was playing with the head lamp realy and it seemed they worked, and the next day they didnt so i have replaced relay still no go and i cant get high beam now unless i pull indicator back towards me to flash high beams , with indicator pushed forward in its traditional constant high beam this function will not work as i did previously either, so no high or low beams now can you help

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: Headlight 2004 camry

your module in the steering wheel is faulty you should get it replaced. you can purchase it at ie Napa for alot less than through a dealer.

Posted on Sep 01, 2008

Ad
  • 1861 Answers

SOURCE: No Hi Beam on 93 Camry

The headlamp circuit is rather simple. From the 15 amp RH headlamp fuse, there is a red w/yellow trace that goes to the RH high beam. Out of the 15 amp LH headlamp fuse, the wire going to the LH Hi beam is solid red. Both of these wires should have power when the headlamp relay is energized. The wires from the Hi Beam bulbs going back to the switch should both be red w/black trace. The wire going from the headlamp relay to power the 2 15 amp fuses is white. The headlamp switch applies a ground to illuminate either the Lo Beams or the Hi Beams.

Posted on Sep 11, 2008

SOURCE: low beam headlights on 2004

You may have replaced the high beam by mistake. The low beam is closer to the exterior (the sides of the car)
Paul G Schmidt
Paulgms@juno.com

Posted on Oct 27, 2008

  • 46 Answers

SOURCE: headlights wont turn on but high beams do on my camry

Have you tried new bulbs, its rare but both low beams may have blown at the same time, it has happened to me in the past.
I don't know your car but the high and low beams could be fused separately so you are left with at least one set in an emergency.

Posted on Jul 02, 2009

  • 7 Answers

SOURCE: my high beams dont work.

high beam switch is faulty look at getting a new stalk.....

Posted on Aug 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the headlamp relay on a 2007 saturn ion


Are both low beams an high beams not working ? What engine does your car have ? Low beam relay only on 2.2 L .
On vehicles with manual headlamps, the LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low beam lamps and high beam lamps at all times. The low beam and high beam circuits continue through the fuse block - under hood, through the body control module (BCM), and to the headlamp switch. The low beam or high beam circuit then, depending on the position of the dimmer switch, continues through the headlamp switch. When the headlamp switch is placed in the ON position, it provides a ground path for the low beam or high beam lamps through G203. The low beam and high beam circuits are monitored by the BCM.
Is there B+ voltage at the headlamp fuse's ? Power runs from fuse through the head lamps to the dimmer switch through the head lamp switch to ground when turned on . If there is B+ voltage at the fuse ,check for voltage at the headlamp switch .
The

Oct 16, 2016 | 2007 Saturn Ion

2 Answers

Replaced the head lamp bulb but only works on high beam


Make sure the other filament is good and that it is receiving power. If no power check relays, fuses, switches,etc for low beams.

Mar 31, 2016 | 2008 Pontiac Torrent

1 Answer

Low beam relay


check the ground wire first... and plug the bulb into the other side, does it work over there ??? NO, bad bulb

Dec 28, 2013 | Toyota Cars & Trucks

1 Answer

2003 Toyota Camry driver's side low and high beams are out


If you have a short it is in the power line to the lamp unit. From the relay.

Apr 10, 2013 | 2003 Toyota Camry

1 Answer

Hight beam wont come on


If you check to make sure your headlight switch connector is plugged in correctly and all other connections are made then the head light switch ( high beam portion) internal connections aren't making a good enough contact or are broken. In this case replace switch.
2_27_2012_8_16_21_am.gif

Feb 27, 2012 | 1986 Hyundai Excel

1 Answer

Headlight problem: 84 Toyota SR5 4wd wagon. When I got the car the high beams didn't work. Replaced both bulbs, still didn't work. Returned bulbs and replaced again, everything worked. A few weeks...


Have you tried replacing the relay as the internal contacts do eventually get to a point, because they switch latge currents, where they do not make a proper contact ? From memory,Toyata vehicles of that decade , the headlight relay was used to switch the earth side of the headlight circuit and operated by toggling between the high and low beam circuits. They also had a separate fuse for each of the the high and low circuits rated around 15 - 20 Amps. You could use a test lamp or multi meter on the contact pins on the rear of the globe socket to check if power is getting the globes. Also check any points where earth leads are attached to body near the relay box as a bad earth could also attribute to the problem. If necessary disconnect, clean thoroughly by removing any paint or corrosion an reconnect securely.
Don't forget to rate this post !!

Oct 09, 2010 | 1991 Toyota Tercel

2 Answers

Camry headlights not working


it sounds like a bad light switch

Mar 25, 2010 | 1993 Toyota Camry V6

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

3 Answers

No Hi Beam on 93 Camry


The headlamp circuit is rather simple. From the 15 amp RH headlamp fuse, there is a red w/yellow trace that goes to the RH high beam. Out of the 15 amp LH headlamp fuse, the wire going to the LH Hi beam is solid red. Both of these wires should have power when the headlamp relay is energized. The wires from the Hi Beam bulbs going back to the switch should both be red w/black trace. The wire going from the headlamp relay to power the 2 15 amp fuses is white. The headlamp switch applies a ground to illuminate either the Lo Beams or the Hi Beams.

Sep 10, 2008 | 1993 Toyota Camry V6

Not finding what you are looking for?
1991 Toyota Camry Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...