Question about 1999 Chrysler LHS

1 Answer

1997 Chrysler LHS 3.5 cars turning over, no spark, plenty of fuel...looking for the crankshaft position sensor...can you tell me the location?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Good Evening, I know you might be having a harder time finding that sensor. It is not in the place a usual car would be, instead it is on the passenger side in the front part of the transmission. If you look in your engine compartment and take off the breather (air intake) tube now look down right passed the motor right past the bell bolts bout 3 inches or so it is right there held in by a 10mm if i remember it right. Hope this helps, and if you have any more questions please feel free to ask.

Posted on Sep 01, 2010

  • earl cleveland Feb 13, 2011

    If you replace the sensor and thats not the problem then it is most likely your Coil Pack 40 dollar part at auto zone



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sebring 1997 I need picture to lookat the PCM sensor and the Crankshaft position sensor (CKP sensor)

On 1997 Chrysler Sebring 2.5L MFI 6cyl...
- the PCM is located in the left side of the engine compartment, beside the Power Distribution Center (PDC).


Fig. 1: Location of the PCM on the Cirrus, Stratus, Sebring convertible and Breeze models


Fig. 2: Location of the PCM on the Sebring coupe and Avenger models

- the Crankshaft Position Sensor is located: under hood, driver side, upper engine area, mounted on end of engine block


Fig. 4: Location of the crankshaft position sensor on 2.5L engines

Hope helps; remember to rating this answer and leave some testimonial comments.

Oct 09, 2011 | 1997 Chrysler Sebring

1 Answer

Need to know how to replace a crankshaft sensor for a chrysler lhs 1996

The crankshaft sensor is located on the driver side of the vehicle, above the differential housing. The bottom of the sensor sits above the drive plate.
Drivers side just above oil pan just behind differential
  1. Disconnect the negative and positive battery cable.
  2. Remove the battery.
  3. Unlock and disconnect electrical connector from crankshaft position sensor.
  4. Remove sensor mounting screw. Remove sensor

Sep 24, 2011 | Chrysler LHS Cars & Trucks

1 Answer

Car would not start

I would start by checking for spark, if no spark check your crankshaft position sensor down by the transmission on the pass side, or the camshaft sensor up in front of the engine also you may look in where the camshaft position sensor is to make sure the belt is still turning.

Jul 23, 2010 | 1996 Chrysler LHS

1 Answer

1997 chrysler lhs turns over but no spark. already changed Cam pos. Sensor and Coil block

Try the crank sensor this is the sensor most likely to cause this not the cam sensor. To get to the crank sensor you will have to jack up the passager side of the car and the sensor is located on the transmission bell housing about 3/4 of the way up on the trans were it connects to the engine.(all on the passager side of the trans) It has a 3 wire plug and one 10mm bolt that holds it in. Hope this helps

Mar 06, 2010 | 1996 Chrysler Concorde

1 Answer

Oil in 1 1997 chrysler lhs spark plug tube

although I am not familiar with this particular engine my son's Mazda Miata had oil in the plug holes and it only required a new valve cover gasket to fix it.

Oct 18, 2009 | 1997 Chrysler LHS

2 Answers


Try removing air inlet hose at throttle body,and open plate up by turning throttle linkage slightly (engine off) and spray a shot ( second or 2 ) of WD-40 into throttle body, then try to start and see if it try's to start, or starts for a second then dies. If it does, you got a fuel delivery problem. Can you hear fuel pump hum at all in rerar of car when you turn key just to on position? (not start)

Aug 08, 2009 | Chrysler LHS Cars & Trucks

3 Answers

Crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

May 02, 2009 | Chrysler Pacifica Cars & Trucks

Not finding what you are looking for?
1999 Chrysler LHS Logo

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides