Question about Mitsubishi Galant

Open Question

I need complete hose hook up diagram on 2003 mitsubishi galant 4 cyl took off intake manifold and cant remember how all the hoses go to it and around it

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mcalkins3
  • 123 Answers

SOURCE: Where is the vacuum hose

IF the engine was revving high RPMS it had to be a serious vaccum leak. If the PCV came undone it would cause it rev up quite high. the shaking was from the factory set RPM limiter when not in gear (around 4,000 RPMS) the only other vaccum leak big enough would be for the brake booster. They both have a check valve but that doesn't mean much. I would start there PCV is around 5 bucks and the other is about the same. If you need pics of location I could do that also.

Posted on Sep 15, 2008

  • 66 Answers

SOURCE: oil coming up out through air intake hose

possible worn out motor but before i say that ck to see if the intake gaskets are blown is it a 5.0 or a 5.7 or a 3.4

Posted on Jan 24, 2009

SOURCE: Oil in the intake manifold air hose...

This is usually an indication of "blowback" caused by worn piston rings. How many miles on the engine? There is not a cheap solution if it is blowback.

Posted on Apr 28, 2009

  • 507 Answers

SOURCE: need diagram of vacuum hoses for 1993 ford

you need to change the modulator on the trans as its vacuum controlled and itsdamaged letting auto fluid get sucked up the line,(diaphragm probably split in modulator

Posted on Oct 28, 2009

anderza
  • 41 Answers

SOURCE: trouble code po171 for engine running lean

I have a website that may help

http://www.kia.ca/content/owners/ownersmanual/2001_sportage_owners_manual_en.pdf

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the thermostat in my 95 Isuzu rodeo 3.2 ltr. V6


where is such a simple word
where;
3.2L V6, SOHC head 6VD1 (not the 6vd1w twin cam heads)
x marks the spot
asked many time here, and same answer.
if you look , you see it, then see its not possible to get to the 2 rear bolts (telling you what?)
pull engine block, ? no
pull intake, yes.

here-bp54dlzlp0pmj5fwzd335nwr-4-0.jpg

Mar 07, 2017 | Isuzu Rodeo Cars & Trucks

3 Answers

Where does the vacuum line come from on a 2003 envoy


from a fitting on the inlet manifold.

Aug 15, 2014 | 2003 GMC Envoy

1 Answer

My 2001 Mitsubishi Galant 4 cylinder is idling high in park and when put in drive it starts idling low, runs rough, and acts like it wants to die at stop lights


This is a typical vacuum leak. Check all the hoses. If none are sucking air then use WD40 and spray around the intake manifold. If the engine runs better or changes how it runs then look at replacing the intake manifold gasket.

Sep 26, 2011 | Mitsubishi Galant Cars & Trucks

1 Answer

99 Mitsubishi Galant, engine is over heating. Where is thermostat located?


I have a 4 cyl engine in my galant and the thermostat is found by following the LOWER radiator hose. You will need to remove the battery in order to gain access to the thermostat housing mounting bolts. There is a video on Youtube.com showing the removal and replacement of the thermostat and radiator for a 1999 mitsubishi galant.

http://youtu.be/Er1szRKrk7c

Nov 01, 2010 | 1999 Mitsubishi Galant

2 Answers

2003 MITSUBISHI GALANT 4 SYL IT STOLL EVEN THOU IT HAS A FULL TANK OF GAS.THE ARTENATOR AND BATTERY ARE GOOD.


check intake manifold hoses including the big one to de air filter ...make shure u got gas and spark ..if the chack engine light is on ..post de codes.

Apr 23, 2010 | 2006 Mitsubishi Galant

1 Answer

2002 Mitsubishi Galant gets poor acceleration.


LOOK AROUND THE AIR INTAKE HOSE.MAKE SURE IT IS INTACT NOT LOOSE.CHECK ALL VACUUM HOSES ON INTAKE.MAKE SURE THEY ARE IN PLACE.

Aug 17, 2009 | 2001 Chevrolet Impala

2 Answers

Spark plugs


in the center of the valve covers it will have coils bolted on top or wires going into valve cover

Aug 05, 2009 | 2003 Mitsubishi Galant

1 Answer

Hose that attaches to back of thermostat housing is leaking


The hose is a cooling by-pass hose. It makes a big horseshoe and attaches under the front of the intake maniold. I think that if you have small hands and a lot of patience you can likely replace it without haveing to take half the engine apart. (You have to pull the head to pull the intake manifold).
I think if you remove the battery, and have a small bright light you will be able to see where if attaches under the front of the intake manifold. Advance auto sells the by -pass hose for
around $12.00 I think.

Becare if you are probing around there are way too many vaccum lines under the manifold.
If they come off and you don't know where to put them -- you are in deep kim chee. I know I am
in super deep Kim chee now.

Hope this helps

Nov 21, 2008 | 1990 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...