Question about 2001 Mitsubishi Eclipse

2 Answers

How do take my flywheel off my 2000 mitsubishi GT I can't find a socket that fites the bolt

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 2,100 Answers

Are you removing the transmission? Is the problem , you can't get a socket or wrench on the bolt? Or you can't find one to fit the bolt? It should be 14mm, 6 point box wrench, or a 6 point socket cut in half with a dremel will get in there. you have a couple windows there to go through. one at the starter, and the other usually on the top right. you have to turn the engine by hand to bring the bolts around, pull out a couple spark plugs to make it spin easier, there are only 3 or 4. But they are a pain. Check it out, hope this helps.

Posted on Sep 01, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

You are going to have to have the correct socket.

Posted on Sep 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove my fly wheel?


This is not an easy job and requires a substantial amount of knowledge. you will also need a decent floor jack or a transmission jack. The transmission must be pulled or slid back to get the flywheel off the engine. The first thing is to take the transmission dust cover off or in some cases the starter. The starter needs to come out anyway. This will reveal the torque converter bolts. You can use a pry-bar to turn the flywheel around so you can get to each torque converter bolts. The other option is to turn the crank with a socket and breaker bar from the front of the engine/harmonic balancer. Then you must drop the transmission or if you can slide it back enough to reach the flywheel bolts mounted to the crank. Once you remove the center bolts in the flywheel it should drop out.

25882486-p1aus1s3fwe0ue1iewji4qiu-2-0.jpg I hope this helps!

Sep 27, 2015 | 2000 Oldsmobile Intrigue

1 Answer

I'M LOOKING FOR FLYWHEEL FOR 1994 MITSUBISHI RVR-WHERE CAN I GET IT


FWD and AWD RVRs have different size flywheels. On you 94 it may be a 6 bolt but is more likely a 7 bolt variant. Try on rockauto.com for parts.

Feb 19, 2015 | Mitsubishi Cars & Trucks

1 Answer

Flywheel bolt size


I'm thinking here that the head of the bolts is not very thick in which case the socket you are using will need some modification. If you look in the socket you will see that there is a small lead in relief and this will only allow the socket to full engage on 1/2 of the bolt head. Place the socket in a vice and use a grinder to grind of the face of the socket until the sides are square across. This will give full contact with the bolt head inside the socket.. Another point, it is unusual to find metric bolts in a USA made engine so check out the other size metric sockets as European metric use 9-11-13-15-16-18-20 mm sizes compared to Asian 10-12-14-17-19-21 mm. in auto production.

Apr 22, 2014 | Chevrolet Tracker Cars & Trucks

1 Answer

Cylinder head torque specs for opel corsa 8valve 1.4l 2005 model


Corsa 1.4I Engine code Z14XE 2000-2004
Bolts must be renewed
stage 1. 25Nm
stage 2, + 90 degrees
stage 3. + 90 degrees
stage 4. +90 degrees
stage 5. + 45 degrees
Sequence
10 6 2 3 7
9 5 1 4 8
bolts 7 & 8 are nearest to the flywheel side of the engine
Engine code C14NZ 1993-1998
Stage 1. 25Nm
stage 2. + 60 degrees
stage 3. +60 degrees
stage 4. + 60 degrees
Sequence as above.
Corsa 1.4I Engine code Z14XE 2000-2004
Bolts must be renewed
stage 1. 25Nm
stage 2, + 90 degrees
stage 3. + 90 degrees
stage 4. +90 degrees
stage 5. + 45 degrees
Sequence
10 6 2 3 7
9 5 1 4 8
bolts 7 & 8 are nearest to the flywheel side of the engine
Engine code C14NZ 1993-1998
Stage 1. 25Nm
stage 2. + 60 degrees
stage 3. +60 degrees
stage 4. + 60 degrees
Sequence as above. <br />Corsa 1.4I Engine code Z14XE <b>2000-2004</b><br />Bolts must be renewed<br />stage 1. 25Nm<br />stage 2, + 90 degrees<br />stage 3. + 90 degrees<br />stage 4. +90 degrees<br />stage 5. + 45 degrees<br />Sequence<br />10 6 2 3 7<br />9 5 1 4 8<br />bolts 7 & 8 are nearest to the flywheel side of the engine<br />Engine code C14NZ <b>1993-1998</b><br />Stage 1. 25Nm<br />stage 2. + 60 degrees<br />stage 3. +60 degrees<br />stage 4. + 60 degrees<br />Sequence as above.

Jan 09, 2013 | Opel Corsa Cars & Trucks

1 Answer

I have a 2000 mitsubishi eclipse gt, it only has reverse and second gear


look at the revers fuse mine was bad a wire was rubbing a bolt under the air cleaner hose hope this helps you

Dec 25, 2011 | 2000 Mitsubishi Eclipse

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

1 Answer

How do i change crankshaft pos. sensor on 2000 eclipse gt 3.0. vehicle runs fantastic but everyonce in a while engine flutters like your popping the throttle, pretty violent, check engine light came on and...


the sensor shoudl be behind the timing cover the bottom gear as teeth sometimes you can get it off without removing the gear on some 3.0 hole driled on lower side of block ,if its a chrysler engine look at bell housing they have a flywheel with holes in them the cranck sensor will be bolted somewhere around the bellhousing of trans aginst the engine

Nov 14, 2010 | 2000 Mitsubishi Eclipse

1 Answer

Golf gt tdi just fitted new duelmass flywheel and gearbox but now got a bad vibration through the car?


I'm just guessing... Are your fly wheel bolts new? VW recommends NEW fly wheel bolts. Sometimes when you secure the axles specifically the inner CV joints to the drive flanges, may some how bind inside the casing (cage) and cause the vibration.

Clutch disc installation:
Tighten bolts diagonally to ensure that pressure plate is seated squarely on the flywheel without distortion. If not seated and torqued evenly, chattering and engagement problems may result.

Mar 06, 2010 | 2000 Volkswagen Golf

1 Answer

Bolt torque specs for flywheel, pressure plate, bell housing bolts for 97 Nissan maxima


1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Jul 07, 2009 | 1997 Nissan Maxima

3 Answers

Timing belt guide bolt


the inspection plate is on the bell housing of the transmission you can use a big!!! screwdriver to jam the flywheel and then remove damper bolt. alot of times if it gices me too much troulbe i remove the right front tire and use an impact gun and socket this usually does the trick. please rate this

Sep 01, 2008 | 2000 Mazda Protege

Not finding what you are looking for?
2001 Mitsubishi Eclipse Logo

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...