Question about 1993 Cadillac DeVille

1 Answer

Rear Drivers side wheel well problem pipe broke

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

Hello, If you are refering to a brake line the best thing to do is see if you can get one from a recycle yard. There are no ready made brake lines in parts. You have to buy new line and make it yourself or have someone else make it for you. After installing the new line you will have to bleed the brakes. Go for it.

Posted on Sep 01, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Why would my rear drivers side wheel lock up when driving

I can help with basics. I need year--make--model? I'd remove tire and check the brakes. Are you rwd? I need more info?

Jul 31, 2015 | Cars & Trucks

1 Answer

I need a rear for my 1985 ford f 150 4wd truck.

For an F150 code 16 could be 3.50 but I'm not sure about a 1985 truck.
You can always jack up one wheel and count how many times the driveshaft turns for one turn of the tire.

Feb 22, 2014 | 1985 Ford F150

1 Answer

I have a rover75classic 54 it is leaking water when it rains on near side is it a useual fault

Had same problem. Lift up rear seat on drivers side and you will see a steel tube running from the wheel arch under the seat. Tube is about 2 inches wide. If this is rusted underneath then water is getting via the wheel arch open end of the tube. It runs into the rear foot well and forward into drivers footwell, also runs under rear seats and into the boot! I removed the rear drivers side wheel, pulled away the plastic wheel arch lining then sealed the hole where the wiring leads through this pipe. Covered it with plastic flashing replaced the wheel arch lining. Took 30 mins to repair, took a week to dry the carpet, rear seats and boot carpet.

Jan 20, 2013 | 2000 Rover 75

1 Answer

Rear brake pipe broke off inside the rear drum how do i get the broken piece out and hoe do i repair it again to working condition

remove the wheel of the drum then remove the drum if its stuck you gonna have to use a hammer a bit after you removed the drum remove that broken piece i recommend that you buy a new one to replace the broken then ur done

Sep 03, 2012 | 2005 Toyota Tazz 130

1 Answer

Differential carrier

if you have rear wheel drive you could have a broke C LOCK on the inside of the differential whicn means you have to remove rear differential cover to replace C LOCK on driver side.

Aug 25, 2012 | 1985 GMC S-15

1 Answer

1991 buick park avenue brake problem had busted brake line on drivers side rear brake so i fixed it then bleed the brakes.aint getting no brake fluid comming out of the passenger side rear so took of the...

Hi Chris, The brake system is basically very simple. If you have duel braking on your vehicle, the usual method is having two brakes operate on the front with for example the left rear and the other system will also operate two front and the right rear. This type of system will have two calipers on each of the front wheels. The tandem system works in a slightly different way, having the forward part of the cylinder pressurizing the rear brakes and the rear part of the cylinder pressurizing the front. I think under the circumstances you are describing, I would have a friend sit inside and pump the brakes repeatedly until the system becomes pressurized (maybe twenty thirty times of pumping the brake pedal) and then ask him or her to keep it pushed firmly down until you find out where its leaking. The amount of brake fluid you report having been sed would indecate a severe leakage. Check the lower parts of the rear wheels for signs of leaking wheel cylinders and then dito for the front wheels. Any signs of wetness at these areas and along the brake system (the plumbing or pipe work) will indicate where the leakage is. If you cannot identify a wheel which is leaking, carefully inspect around and blow the master cylinder and if this no sign go along the fluid lines, taking special note of where the damaged pipe was repaired. If there is a blockage in the line, air may be trapped at that point causing difficulty in pressurizing. Once the place of leakage has been identified it must be attended to before bleeding the system. When bleeding, begin with the wheel furthest from the master cylinder, and work your way back to the master cylinder one wheel at a time, until you reach the closest.Keep in mind that you may find it required to pump the pedal many many times before opening the bleed nipple.Regards John

Oct 29, 2011 | 1991 Buick Park Avenue

1 Answer

Where do i find the purge valve on a jeep grand cherokee 2001 i have engine codes p0445,p0443,p0442, gas mph seems to have dropped, muffler and tail pipe have turned white. What could be going on?

The purge valve is located under the hood on the drivers side fender, the most likely cause of your problem is a cracked emissions hose near the vapor canister. To access the leak detection pump and vapor canister remove drivers side rear wheel and inner splash shield. then remove the metal shield that protects the canister and check all of the hoses.

Jan 20, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Truck will only go in reverse and not forward

i had this problem on my 1994 k1500, i took the drivers side rear wheel off and the hub had locked up beat it with a hammer and it broke free, lubed everything up and has stayed freed up for over two years- still running strong. Hope this helps

Dec 11, 2010 | 1994 Chevrolet K1500

2 Answers

Need to replace brake line going to drivers side

You can take the line off and take to a parts store that sells metal brake pipes by the foot,there is different size pipes as well as flared end nuts.You will have to bend the pipe to fit then bleed the brake system.Iwould suggest to take it to a shop and have a pipe made up.

Aug 22, 2009 | 1996 Buick Skylark

2 Answers

91 accord rear wheel won't spin when put in drive

check the brake, hand brake cable, differentail, driver train. in that order.

May 20, 2009 | 1991 Honda Accord

Not finding what you are looking for?
1993 Cadillac DeVille Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides