Question about 1984 Nissan 300ZX

1 Answer

1 how do i replace wheel studs on a 1984 nissan 300zx 2 is there a c-clip on the axel of the rear side of a 1984 nissan 300zx

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

You should not have to take axle out to replace studs.

Posted on Sep 01, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1984 300zx which way does the flow on the fuel filter go

There should be an arrow painted on the side of the filter.
The flat side usually connects to the fuel injector side of the line.

Jul 31, 2014 | 1984 Nissan 300ZX

1 Answer

I have a 1992 nissan terrano only my left rear wheel is getting power in 4WD

C clip that retains axel is broken or came off. Or the axel is bad.

Jan 12, 2014 | Nissan Cars & Trucks

1 Answer

Stalling problems with a 1984 Nissan 300zx?


Nov 22, 2011 | 1984 Nissan 300ZX

1 Answer

How to replace a lugnut stud on a 85 nissan pickup

Depending on if its a rear axel or a front rotor how you're going to do it is different. The method is still the same though.

The studs just have a serrated edge right under the head that holds them in place. They just need to be smacked out with a sledge hammer and the new stud came be pulled back in with a good lug nut and some washers that the studs will fit through without binding.

For instance,
A front rotor would need to be pulled off the vehicle. Looking at the back side you can see the head of the stud. Place the rotor on a firm surface and hit the stud from the side that is broken to drive it out through the back side.
Put the new stud in from the back side. Try to turn it to where it feels like the grooves (serated area)on the stud are locked into the grooves on the rotor. Then put some large washers over the threads (so if there is a shoulder on the stud that comes through the nut will not bottom on it). Put the nut on and tighten it do bring the stud through.

Sep 19, 2011 | 1985 Nissan Pickup

1 Answer

Want to know colors for radio 88 300z sum one cut factory harness

Hope this is what you are looking for and hope it helps....Good luck.

1984-89 Nissan 300ZX Stereo Wiring Constant 12V+ Red/Black Switched 12V+ Blue Ground n/a Illumination Red/Yellow Dimmer n/a Antenna Trigger Green/Black Antenna Left Rear Front Speakers 6 1/2" Doors Left Front (+) Blue/White Left Front (-) Blue/Yellow Right Front (+) Brown Right Front (-) Brown/White Rear Speakers 6 1/2" Side Shelves Left Rear (+) Red Left Rear (-) Green Right Rear (+) Blue Right Rear (-) Pink

Mar 22, 2011 | Nissan 300ZX Cars & Trucks

1 Answer

How do i remove the turn signal switch from a 1984 nissan 300zx?

What you really want to remove is the "Combination Switch" which controls the
a) headlights b) turn signals, and c) windshield wipers.
The new switch comes with the Left-hand handle attached (expect to pay $$$).

I found your solution (with illustration and replacement parts) at
Autozone will expect you to register with the site - free. Since your car is a 1984, buy
a Haynes manual - $20 anywhere (try Pep Boys, Advance Auto Parts, etc.)

(I don't work for Autozone) Autozone sells 2 replacement switches:
the one you want is: Duralast SW1836 $122.99 - it has the combination switch and handle only.
They also sell: Duralast SW1690 $170.99, which has the combination switch/handle and also a
collar going around the steering wheel and another switch and handle on the right side of the column.

1. remove steering column cover.
2. unfasten the wiper switch electrical connector.
3. remove the wiper switch-to-combination switch retaining screws, then pull the wiper switch off of the combination switch.
4. The combination switch is now disconnected and can be removed.
5. Installation of new part is reverse of removal.

Oct 13, 2010 | 1984 Nissan 300ZX

1 Answer

How do iget get sensor light to go off on 1984 nissan 300zx

under dash, steering weel side, there is a cable with a notice about the sensor, just unplug it.

Mar 20, 2010 | 1984 Nissan 300ZX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides