Question about Ford Explorer

1 Answer

My 1998 ford explorer ac stop working , the compresser does not cut on

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

It could be low on refrigerant or the low pressure cutout switch is defective. It is located on the accumulator. You can check it by unpluging the plug at the switch and jumper the two wires together. If the compressor comes on and a/c starts cooling replace the switch. If the compressor doesn't engage check to see if you are getting power at the clutch coil on the compressor. If you do the coil is defective so just replace the compressor assembly. They are so cheap nowdays it's the best way to go.

Posted on Sep 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1998 4.0L Ford Explorer only blows hot air. The vaccum line is broken just above the heater water control valve. Not sure where it connects . I believe I need the diagram to show how it connects.


mmm i had the same problem with my 1998 4.0L Ford Explorer probably a leaking condenser, sounds like you have a problem with your AC system, i suggest taking it to a ford servicing centre.

May 03, 2011 | 1998 Ford Explorer

1 Answer

2002 ford explorer open door beep goes on and off more so in the winter. what wire can I cut to stop the beeping?


The door sensors are "crush" style, and over time the switch compresses too far, Buy new switch(es) and replace, Pulling old one will be extreme short term repair.

Sep 21, 2010 | 2002 Ford Explorer

1 Answer

Abs cuts in as the car stops


You have a wheel speed sensor on each front wheel, and one for the rear. If one of these goes bad, your ABS will activate. (It think your wheels are turning at different speeds) Get them checked.

Jan 02, 2010 | 1998 Ford Explorer

2 Answers

FREE ONLINE DOWNLOADS OF WIRING DIAGRAMS


i ned my home hetr and ac wiring diagrams to thral contral

Sep 30, 2009 | 1998 Ford Explorer

1 Answer

Ac work on max ac only, all other controls blow hot air


There is a Flap on heater box and on some of those it is motor controlled, but it sounds like the flap is not switching back and forth

Sep 16, 2009 | 1998 Ford Explorer

1 Answer

AC Compressor clicks


The noise is the clutch on the front of the AC Compressor. This is a common problem on late ninety's Doge Rams. The clutch is inside the AC pulley. It is electronically controlled. Their are two wires coming off the AC compressor near the pulley. Follow these two wires and you will find a wiring harness connector that you can pull apart. Disconnecting this connector will stop the clutch from activating, saving you a little bit of gas too. But the AC will not work while these two wires are disconnected. I disconnect these for the winter to save on gas and noise. I don't know what causes these to activate so much.


daf8271.jpg

Aug 17, 2009 | 1998 Ford Explorer

1 Answer

1996 ford explorer a/c not working


Get it purged and recharged first at a AC shop.

Aug 13, 2009 | 1998 Ford Explorer

1 Answer

2003 ford explorer ac compresser wont come on


possibly low on freon thers a switch that will not let it engage if pressure is to low!!! hope this helps you!!!also check for 12v at compressor!!good luck!!!

Jun 22, 2009 | 2000 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...