Question about 1996 GMC Sierra

1 Answer

96 6cyl. GMC won't start. I was driving and it just cut out. It has spark at the plugs and gas up to the intake but plugs are dry.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Cant get the hoen to work . Whin i press the horn i can hear a click.

Posted on Sep 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my 1996 mercury sable not starting?


Can be out of gas, blown fuel pump fuse or injector link, defective fuel pump relay, broken wire, or of course defective fuel pump. Or a number of other defective relays or switches. Or possibly the problem is in the electronics, NO spark to the plugs. First check for spark, then test fuel pressure at the engine intake area.

Jun 21, 2014 | 2002 Mercury Sable

1 Answer

Won't start not firing where do you spray intake starter fluid?


into the air intake where the air filter goes

Aug 14, 2012 | 1999 Audi A6

1 Answer

My 98 gmc 1500 V8 5.0l won't start. Has good spark


Spray starting fluid into the air intake of the engine, if it starts and you have fuel pressure you have no injection or injector pulse as we call it. Check ECM fuse one and two for continuity if it starts with fluid..

May 25, 2012 | 1998 GMC Sierra

1 Answer

2000 blazer won't start


As for it cutting off i would take the mass air flow sensor off and clean it with a non-chlronated brake cleaner then let dry for 15 minutes and re-install.As for engine not cranking overmost likely its the starter solenoid that is bad.

Jan 02, 2012 | 2000 Chevrolet Blazer

1 Answer

Turns over won't start getting gas up top to fuel injectors, but won't start


GIVE IT A SHOT OF STARTING FLUID IN INTAKE IF IT RUNS FOR A MINUTE THE CONTROLER FOR INJECTIORS HAS PROBLEMS IF NOT CHECK FOR SPARK AT SPARK PLUGS THIS WILL TELL YOU REALLY WHAT SYSTEM YOUR HAVEING PROBLEMS WITH. USALLY IF THERES FUEL AT INJECTORS ITS A SPARK PROBLEM GOOD LUCK

Aug 20, 2011 | Dodge Neon Cars & Trucks

1 Answer

Heavy rain, stalled a couple of times. Now barely starts, sounds muffled when it does start, low power when driving, engine light keeps blinking, won't stay started once take foot off gas, started...


Pull distributor cap and dry it off. Dry the wires. Not fixed? Change the spark plug wires.This rotary is wet at a source in ignition circuit.

Aug 15, 2011 | 2004 Mazda RX-8

2 Answers

I ran in to a pondle of water when it was raining now when i start my car it starts but it will cut off but i can sit there hold tha gas for a min then it be ok but sometimes it act like it want to cut off...


A car will stall when driven through standing water if the ignition system is not watertight. Worn spark plug wires and coil wire, improperly seated spark plug wires, or loose distributor cap are all possibilities.
There is a spray called CRC or some agent that promotes a water drying action can be used to dry out a wet distributor cap and wires. Drying off the electrical components will remove the moisture that is grounding the electrical energy that should normally go directly to the spark plugs.
If car will not restart after stalling from the water splashing as described in the question - and the poor condition of the electrical system is ruled out, some water may have passed through the air intake into the engine and perhaps into the cylinder. If this happens have the car towed to a repair shop where they can remove the water before any further damage results. This condition is not easy to occur but a real deep puddle can set the stage for water to be sucked into the air intake and pass through the filter into the intake and through the valves into the cylinders. This is why you see a Hummer with a snorkel - for wading through deep water.
Read more: http://wiki.answers.com/Q/Why_does_your_car_stall_when_you_drive_through_a_puddle#ixzz1CuKhPDHg

Please rate me!

Feb 03, 2011 | 2001 Pontiac Bonneville

2 Answers

Im getting spark for the plugs and im getting fuel. i even put starter fluid in the intake and gas but it wont start it just turns over and nothing


A 1999 GMC Yukon has a fuel-injected engine. They are known for the fuel injector lines inside the intake plenum to break and flood the engine. If you are pouring starter fluid and gas in the intake you are only making it worse. replace the injector assembly with the "new improved" injector assembly and replace the plugs, then it will probably start.

This subject is covered by GM Technical Service Bulletin No.: 00-06-04-003B

See GM Parts List below. This replacement Injector assembly is now also available in the aftermarket.
f098b90.gif

Nov 11, 2009 | 1999 GMC Yukon

1 Answer

Wont start my truck


have a 1997 gm sierra pickup want start new plugs new gas filter have spark at the plug pressure on gas line checked fuses v8 350 2 whell dr

Sep 27, 2008 | 1997 GMC Sierra

Not finding what you are looking for?
1996 GMC Sierra Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...