Question about 1998 Jeep Cherokee

1 Answer

Signal and hazzard lights not working. Can you tell me which fuse to change?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

I would also look at the blinker relay.It's a combination blinker/hazard relay.It's up under the dash on the left of the steering column.Hope this helps

Posted on Sep 03, 2010


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 61 Answers

SOURCE: I have no brake lights,

there is a short somewhere-try disconnecting all components on that circuit,put new fuse and try using one,if the fuse still blows,problem is in wiring or switch unit,if not,plug one component in and a time until the fuse blow,replace component
accordingly.make sure there is no slightly shaved wire touching the chassis,this will show when all if d/c'ed and fuse still blows,good luck

Posted on Aug 12, 2008

  • 79865 Answers

SOURCE: Turn signal

u need to replace the turn signal flasher.

Posted on Dec 16, 2008

  • 2 Answers

SOURCE: 99 Dodge Ram 1500 4x4 / nothing but parking lights,no flashers or brake lights......

I found the problem on my Dodge Ram van.. The button for the hazard lights was bad.. I tuned on the hazard lights and only had one side, so i jiggled it and the other side came on. Then I pushed in the hazard button to turn them off and proceeded to check the brake lights, the still did not work so I again jiggled the hazard button and whaaalaaa the brake lights would flicker on and off.. I have a piece of cardboard pushing the button to the side to hold pressure on it keeping my brake light connection until I can get me a new hazzard switch.. Hope this helps..

Posted on Mar 05, 2009

  • 957 Answers

SOURCE: 2006 Honda CRV Signal/Hazzard Lights not working

How did you check the flasher relay? I only ask because it is a circuit board. But anyways if you feel confident that its fine then I've seen the multi-function switches fail. IM talking about the the lever on the steering column, behind the steering wheel. If you probe the plugs for signal/hazard lamps and you have ground but no power then I would test the multi-function switch.

Posted on May 14, 2009

  • 160 Answers

SOURCE: my 1999 ck 3500 chevy truck signal and hazzard

There is a make or break circuit between the fuse box and the computer that may have sprung. If you find the relay, there is a small small hole in it. You need a toothpick, put the toothpick in the hole and there is sort of a button in there. You will hear it pop like a spring going into place and then the indicators should work.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

98 dodge ram brake and turn signal and hazzard not working on rear

first thing to do is check your fuse for your signal lights as your hazzard lights are on the same circut! on the left of your dash by the drivers door is a access door that pops off a print out of the fuses is on the fuse door use tweesers to pull the fuse out! use a 15 amp fuse!

Mar 21, 2015 | 1998 Dodge Ram

1 Answer

Brake lights turn signal and hazzards

Turn signals are on fuse number one and brake lights are on fuse number 9. Both are in the fuse box under the dash or on the side of the dash. Both are 15amp.

Jun 22, 2013 | 1995 Ford Mustang

1 Answer

Turn signal and hazzards won't work; have checked fuse and is good.

Flasher been checked? Do lights come on, but no flashing, or nothing?

Apr 18, 2013 | 2003 Dodge Durango

1 Answer

Turn signals and hazzard lights not working

probley popped a fuse mate check ya user mannal for the fuse you need to change or seach online for your type of car should tell you there i done it bear times when changing new radio but never heard of it blowing the turn signals and hazzards normaly just pops the radio fuse

Apr 04, 2012 | 2006 Honda CR-V

1 Answer

Brake light not work. done all checking blubs is good, replace switch, replace relay, fuse all good. turngal work hazzard light work but no brake light. i bypass on relay it work so i cant leave short...

the brake light switch powers the wire which goes to the turn signal switch. So I think if the turn signals works, then the turn signal switch is bad. Check for power at the wire going from the brake switch to the turn signal switch. . Since you didnt tell what year or model the truck is, I cant tell you what the wire color is.

Dec 10, 2010 | GMC C3500 Cars & Trucks

1 Answer

Turn signal and hazzards fail to work, brake lights, tail lights work,but when you apply the turn signal or hazzards lights go out

It sounds like your turn signal fuse might have gone out. It's not just a simple fuse to pull in the 96 Blazer. You actually have to take the lower half of the dash apart to get to it. It takes about 15 minutes in all to do. It's a round fuse right below your stereo almost. Here are a couple of links that I hope might help you!

The simplest way put, go to your local auto parts store and tell them you need a turn signal RELAY. It's the round relay. Then once you have that, go home and take apart your whole dash (you'll know what to look for since you already bought it) and replace it. It all should would after that! Best of luck to you!

Aug 09, 2010 | 1996 Chevrolet Blazer

1 Answer

I have an 1996 pontiac my turn signal went out. all others light work hazzard light is working fuse are good working but no turn signal left nor right

more then likely its the flasher doing this. stop at a auto parts store and they will tell you where it is on your van.

Apr 18, 2010 | 1996 Pontiac Trans Sport

2 Answers

Blinkers wont work

If they will work with hazzard lights turned on then you need a turn signal flasher,after you have checked the fuses of course.If that does'nt cure it then it's either the Signal light switch or bad wireing,but this is not common.

Oct 23, 2009 | Ford F-350 Cars & Trucks

Not finding what you are looking for?
1998 Jeep Cherokee Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides