Question about 2008 Dodge Charger

Open Question

I need to know how to replace outer tie rod ends on an 08 dodge charger?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
justuscc
  • 360 Answers

SOURCE: replacing outer tie rod on a 2000 dodge neon

put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Posted on Oct 03, 2008

Ad
  • 1 Answer

SOURCE: Inner tie rod 99 durango replacement

make sure if you do it youself you count how many turns it takes for your tierods to come off. it it makes it easy for me that way. also make sure you get a front end aligiment when your done

Posted on Dec 07, 2008

michigan man
  • 3533 Answers

SOURCE: replacing outer tie-rods on '98 volvo v70 wagon

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

  • 750 Answers

SOURCE: Loose inner tie rods on '97 Dodge Dakota Sport 2WD

corect size wrench should work. count the number of turn it takes to remove each unit make note and install new units using those numbers

Posted on Jun 29, 2009

wilsodfarm
  • 986 Answers

SOURCE: torque specs. for outer tie rod ends for 2006

Tie rod end is 35 ft. lbs. Pinch bolt for the lower ball joint - 105 .I hope this helps you

Posted on Oct 06, 2009

Testimonial: "thanks for the help"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 dodge charger front end squeaking


First you need to check your outer tie rod ends, then you need to check your lower control arm bushings also you will need to look at the sway bar bushings. That is what I have found worn out on my 2006 dodge daytona charger

Apr 08, 2012 | 2006 Dodge Charger

1 Answer

Where is the inner left and right tie rods at on a 2003 Chevy Silverado Just need to know exactly where they are


The inner tie rod ends are on the other end of the same rod as the outer tie rod ends. They should connect to the drag link and look almost identical to the outer tie rod ends. Hope this helps.

Sep 11, 2011 | 2003 Chevrolet Silverado 1500

2 Answers

My durango had a tie rod break on the front drivers side. I took the piece to the auto parts store and they need to know if it is an inner or outer and the size is either 15mm or 16mm. I do not know how to...


It may be stuck on defrost cycle due to a bad timer... is there an adjustable switch that you could adjust it should start up... let me know......

Jul 20, 2011 | 2005 Dodge Durango

1 Answer

How do i loosen the outer tie rod end to remove it from the bushing once tie rod is out of streeing knuckle i know it will need to be aligined and i need to count treads when putting new outer tie rod end...


You may need a propane torch to heat up the nut on end of outer tie rod. With tie rod still attached to steering knuckle try to loosen the outer tie rod end nut that is connected to inner tie rod. Pull tie rod end back out of knuckle. Use pliers or vise grips to hold inner tie rod end while turning outer tie rod end to the left.

Oct 27, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

Tie rod replacement cost


Hi Gcg_77,
You will need to contact your local auto parts store to get price for the tie rod ends.My flat rate manual listed them at $65 a piece but this is an old price.
The labor time listed for these are as follows:

1 inner tie rod end is listed at 1.4 hours,if you replace both it is listed at 2.0 hours.
1 outer tie rod end is listed at 1.1 hours,if you replace both it is listed at 1.4 hours.
These times include resetting the toe only. If you want a complete alignment you deduct 0.4 hours labor and charge full alignment price.
Hope this helps. If you need anything else,let me know. Thanks,Chuck

Feb 11, 2010 | 2006 Dodge Charger

1 Answer

How hard is it to replace a outside tie rod end on a 95 dodge neon and how.


take the wheel off, there is a nut on the tie ron locking the tie rod end in place loosen this up (only break it free do not back way off) now take the nut offthe tie rod end that goes into the spindle, Hit the side spindle with a hammer right were the end goes in while pulling up on the tierod end (may take a few hard hits)> Now that you have the end out of the spindle you can unscrew the tie rod end from the inner tierod.*******NOTE*******measure the distance between the locknut on the inner tie rod to the middle of the outer tierod end,You want to keep that same distance or your car will pulll to one side and you'll need a wheel allignment.

Dec 30, 2009 | 1995 Dodge Neon

1 Answer

Repair inner tie rod end of 1997 dodge avenger


f734654.gif #3 is the inner tie rod and it is simply screwed into each end of the steering rack. Raise and support the car remove the wheel and you should see where it is connected to the outer tie rod. There is a lock nut that you'll need to loosen slightly to get the tie rod off. You will need to get a wheel alignment once done but by slightly loosening the lock nut, you have a good reference of how it should be once done. Once loose, you should be able to turn the tie rod by using a wrench on the flattened area on the rod. Once disconnected from the outer tie rod end, you should be able to remove the dust boot covering the inner tie rod connection. Mine came right apart so hope you have no problems. After you have it out, here is where the loosened locknut comes into play. Put the new and old tie rod side by side, line up the ends that attach to the rack and pinion then mark the new rod so you know how far to put the lock nut on the new tie rod. Simply tightly screw the new one onto the rack and pinion put the boot back, screw on the lock nut to the mark then attach the tie rod to the outer tie rod end up to the lock nut then tighten the lock nut against the outer end. Get the tire back on, lower the car and Voila, done. Now go get an alignment.

Nov 18, 2009 | 1997 Dodge Avenger

1 Answer

How do you change outer tierod ends on a 1996 dodge grand caravan


jack vehicle up in front and make sure its secure. remove front wheels. tie rod is bolted thru steering knuckle. remove the cotter pin from tie rod end. remove the nut from tie rod end. use a small ball joint splitter and small sledge to release tie rod end from knuckle. if you dot have splitter a good hard hit with small sledge on steering knuckle where tie rod attaches will usually release it. b careful not to bend backing plate. loosen the lock nut on tie rod and spin old end off. try to install new end as close as possible to same position as old end. you will need a front alignment after replacement.

Oct 03, 2009 | 1996 Dodge Caravan

4 Answers

2001 Dodge Caravan outer tie rod how to install it macking noice and shold i change stiblizar too


loosen nut on tie rod..22mm wrench,remove nut from tie rod end..18mm socket,hit side of knuckle with hammer to seperate tie rod end..unscrew tie rod end from tie rod..reverse procedure to install..you will to hold down on tie rod end to keep stud from spinning

Mar 16, 2009 | 2001 Dodge Caravan

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...