Question about Toyota Camry

1 Answer

I have a 1999 camry (v6) and am trying to find out which pins on the diagnostic stick need to be bridged out to correctly set the engine timing. My previous 1994 camry (4cyl) had the following bridged te1and e1.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,016 Answers

Hi,

The terminal connections should be the same TE1 and E1.

Let me know if you need more information.

Thanks

Jason

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Show me the timeing marrks on a1999 toyota camry


This is a Engine 2.2....1999 Camry...

michael_cass_98.jpgmichael_cass_99.jpgmichael_cass_100.jpg

Jun 20, 2011 | 1999 Toyota Camry

1 Answer

I have a 94 Camry. When i accelerate at lower speeds i hear a rattling noise coming front he front end. Do you know what this could be? I thought it might be the exhaust rattling but i also have a...


Hi R,
If I understand correctly the sound you're describing could be something known as 'pinking' It occurs when the ignition timing is too far advanced and can damage the engine. Make sure that you're using the correct octane rated fuel in your vehicle and thereafter take it for a tune. Whoever does it, should set the timing at 10 degrees BTDC. To set the timing correctly, open the diagnostic socket in the engine compartment which when standing facing the front of the car will be on your right and the vehicles left. Open up the cover and bridge between T and E1 (A small directory is inside the same cover, which will help you find the correct connections) Only when the bridge is connected can the ignition timing be set correctly. This should be carried out with a strobe timing light with the engine running.
Regards Johngee10

Feb 09, 2011 | Toyota Camry Cars & Trucks

1 Answer

I have a 1999 camry (v6) and am trying to find out which pins on the diagnostic stick need to be bridged out to correctly set the engine timing. My previous 1994 camry (4cyl) had the following bridged ...


there is no bridging on these vehicles. Those features were only available on OBD1 models prior-1995. May I ask why you are trying to adjust timing??Timing components in these engines are computer controlled!!

Aug 31, 2010 | 1999 Toyota Camry

1 Answer

Timing needs to be set on a 94 toyota camry


Click on the following free direct Link. It has several Diagrams including the correct Timing Belt Diagram for your 1994 Toyota Camry for either the 2.2L DOHC In-Line 4-Cylinder or the 3.0L V6 Engine. Included are Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1994/make/toyota/model/camry/1994_toyota_camry_timing_belt_diagram_marks.htm

Apr 08, 2010 | 1994 Toyota Camry

1 Answer

1999 Toyota Camry V6 idles rough and stalls after starting. No check engine lights and runs fine otherwise. Has only happened three times in the last two months. After keeping the idle up and running car...


yes it could be a fuel related problem, when was your last tune up, it could also be a spark issue, old or corroted spark plugs will sometimes not put out the correct amount of heat to ignite the gas correctly till it runs for a while, if the check engine light isnt lit, it will almost have to be something simular to this

Mar 19, 2010 | 1999 Toyota Camry

3 Answers

Check engine light just came on 1993 toy camry


First you need to find out what the fault code is that is making the check engine light come on. To do this, locate the diagnostic connector under the hood. It will be a black rectangular connector approx 50mm X 25mm with Diagnostic written on the cover. Open the cover and on the inside of the cover will be a diagram of the connections and their different labels. Locate pins labelled TE1 and E1. Switch on the ignition switch without starting the engine and with a small jumper wire bridge between pin TE1 and pin E1. Observe the check engine light on the dash and you will notice that it will be flashing. Read the diagnosis code as indicated by the number of flashes that this light makes. Each code will be displayed by first blinking the first digit of the code, then a pause and blink the second digit of the code. For example, Code 52 (knock sensor signal) will flash 5 times, pause and then flash 2 times, then a longer pause before it goes onto the next fault code if there is another one. Once it has gone through all the stored fault codes it will go through the sequence again starting at the first fault code again. Due to the many different fault codes that can be obtained it would be better to post another question for the fault code obtained. Good luck!

Jan 06, 2010 | 1993 Toyota Camry V6

1 Answer

1993 Toyota Camry V6 Timing Settings


Get a T belt from toyota. It has 3 white lines on it and and arrow mark. 2 lines are solid and one is broken. Put the arrow facing away from the engine. The cam gears have a dot punched into them near a certain tooth. This is where the solid white lines will line up with. The crank gear will have a dot also. It will line up at 90 degrees from the top, towards the front of the car. This is where the broken line will match up with. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct.
Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.

Mar 12, 2009 | 1993 Toyota Camry V6

1 Answer

1993 Toyota Camry Engine light comes on start panel


There is usually a diagnostic box when u raise the bonnet. It is located at the passenger side, close to the body of the vehicle. If u open it, u will notice that there r 2 points E1 & TE1. Bridge those two and observe how the engine light flashes, ie how often after pauses. The blink between pauses represents a digit. Remember it and tell me what number u ended up with

Nov 12, 2008 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...