Question about Ford E-250

Open Question

How do I remove the brake drum on a 1960 F250 Ford Truck?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 74 Answers

SOURCE: Ford F250 Spare Tire Removal

there is a hole in the bumper or when you let the tail gate down there should be a hole. there should be some rods with the factory jack to allow you to let the tire down

Posted on Jun 18, 2008

fknstart
  • 404 Answers

SOURCE: removal of rear brake drum 2002 ford escape

make sure handbrake is off take wheel off hit the drum with a mallet not steel,as it will brake,hit on outter diametter face of drum, try and rotate as you twist off

Posted on Jan 05, 2009

  • 77 Answers

SOURCE: rear brake drums 1998 ford escort

hi to remove the hob nut you need a large bar about two feet long and i think they are 30mm but you will need to replace them with new ones and torque them correctly or you will encounter problems theyalso have to be pinned when torqued it really is not a diy job

Posted on Feb 04, 2009

CMV9
  • 594 Answers

SOURCE: Brake drum 2005 Escape

here is a diagram on how to remove your brake drum. please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
CAUTION Dust and dirt accumulating on brake parts during normal use may contain asbestos fibers from production or aftermarket brake linings. Breathing excessive concentrations of asbestos fibers can cause serious bodily harm. Exercise care when servicing brake parts. Do not sand or grind brake lining unless equipment used is designed to contain the dust residue. Do not clean brake parts with compressed air or by dry brushing. Cleaning should be done by dampening the brake components with a fine mist of water, then wiping the brake components clean with a dampened cloth. Dispose of cloth and all residue containing asbestos fibers in an impermeable container with the appropriate label. Follow practices prescribed by the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA) for the handling, processing, and disposing of dust or debris that may contain asbestos fibers.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the tire and wheel assembly.

    CAUTION Use of a brake drum puller or a torch is not recommended. Brake drum distortion can result.

    NOTE If the brake drum is rusted to the axle shaft pilot diameter, tap the center of the brake drum between the wheel studs.
  3. Remove the brake drum.
  4. If equipped, remove the brake drum retaining clips.
  5. If the brake drums will not come off, follow these steps.
  6. Move the brake shoe adjusting lever off the brake adjuster screw.
  7. Loosen the brake shoe adjuster screw nut by adjusting the nut upward.
  8. Using the special tool, 134-R0191, measure the brake drum inside diameter.
  9. Install a new brake drum if the maximum inside diameter exceeds the specification shown on the outside of the brake drum.
    67197-esca-g51.gif Drum brake exploded view
To install:

WARNING Whenever a wheel is installed, always remove any corrosion, dirt or foreign material present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Failure to follow these instructions may result in personal injury.

  1. Clean the wheel hub mounting surface and wheel pilot.
  2. Install the tire and wheel assembly.

Posted on Apr 16, 2009

  • 32 Answers

SOURCE: How do you remove the rear brake drum?

remove the wheel release the e brake and drum should slide right off no problem

Posted on Jan 05, 2010

Testimonial: "Thanks cyco1976 for the info. very helpful"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear brakes burning


My Bronco had drums and was also the same year. my fathers 87 F250 had drums also. they both had RABS Rear Anti-lock Brakes. Check for broken, missing, or binding return springs

Oct 10, 2012 | 1990 Ford F250

1 Answer

DIAGRAM 95 F250 REAR DRUM BRAKE


Here is a typical Ford drum brake. The long shoe goes to the rear.
9_18_2012_7_05_46_pm.gif

Sep 18, 2012 | 1995 Ford F250

1 Answer

Brake shoes on 1987 f250 460 1987 2 wheel drive how to replace


Lift the front of your Ford F-250 off of the ground using a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench to prepare the truck for servicing. 2 Open the hood on the engine compartment and take the lid off of the master cylinder that bolts to the brake assister on the driver's side firewall.3 Remove the hex-head bolts on the back of the brake caliper with a socket. With the bolts removed, pull the caliper off of the Ford's brake rotor.4 Pull the old brake pads out of the caliper and discard them. Squeeze the brake piston back into the backside brake caliper with pliers, and then insert the new pads into the brake caliper.5 Pull the rotor cap cover off the middle of the rotor with a screwdriver and use a socket to remove the nut located behind the cover.6 Pull the rotor off of the wheel spindle.7 Remove the old wheel bearings from the brake rotor and insert them into the new rotor. If the old wheel bearings are worn, replace them with new bearings.8 Slide the new rotor onto the wheel spindle and secure it using a bolt and socket. After you tighten the bolt, press the cover back onto the rotor.9 Place the caliper on the rotor and secure it with a socket and hex-head bolts. 10 Duplicate the process on the passenger side of the F-250. 11 Close the master cylinder after putting the wheels back on the Ford and lowering it to the ground. Press on the brake pedal to seat the pads against the rotor
Replace the F-250's Rear Brakes 1 lift the rear of the Ford F-250 off the ground with a jack and jack stands. Remove the wheels from the Ford with a lug nut wrench.2 Place a strip of paint on the back of the brake drum and rear brake drum cover so you can position the brake drum orrectly when you put it back on. If you plan to install new brake drums on your Ford F-250, skip this step. 3 Place the brake drum puller on the brake drum and pull the drum from the wheel hub. The method for attaching the brake drum puller depends on the brake drum puller that you use. 4 Remove the springs that attach the brake shoes to the wheel hub by pulling them off with pliers.5 Lift the old brake shoes off of the wheel hub and place the new brake shoes on the wheel hub. Secure the new shoes with the springs.6 Pound the brake drum onto the axle hub with a rubber mallet.7 Duplicate the process on the passenger side of the Ford.8 Put the wheels back on the F-250, lower it to the ground and, then press on the brake pedal to seat the shoes against the brake drum.

Oct 14, 2011 | 1988 Ford F 250

1 Answer

There does not seem to be any where to set up the E brake on my F250 truck, do you have to pull the brake and rotor off.


Yes, the parking brake uses a drum style with shoes. The inner part of the rotor is the parking brake drum. There is an adjustment hole in the back of the backing plate. If it hasn't yet been removed, you may have to punch out the stamped hole and use an adjuster (a screwdriver will work). To get to the parking shoes, remove the caliper and remove the rotor. Good luck.

Apr 08, 2011 | Ford F-250 Cars & Trucks

1 Answer

Need instructions to remove the front rotor on F250 Four wheel drive truck - 2001 year


  1. Raise and support the vehicle; Remove the wheel and tire assembly;
  2. After removing the tire, remove the brake pads;
  3. Remove the disc brake caliper by removing the two disc brake caliper pin bolts. Lift the disc brake caliper from the disc brake caliper anchor plate (2B292). If necessary, remove the V-springs.
  4. Remove the pads. Remove the front disc brake caliper anchor plate stainless steel rail clips.
  5. Remove the rotor.
  6. Note: Perform this step for DRW vehicles. Remove the eight hub extender nuts, the hub plate and the rotor. Remove the eight hub plate nuts. Remove the hub plate. Remove the rotor.

Mar 02, 2011 | 2001 Ford F250 Super Duty Super Cab

2 Answers

Is there a trick to removing a rear brake drum on a 92 f250


Get a brake shoe adjusting tool at any auto parts store to retract the shoes back to a smaller diameter to release the pressure on the brake drum for removal

Aug 11, 2010 | Ford F-250 Cars & Trucks

3 Answers

Changing front disc brakes on 95 ford f250


Thats how I have done it on 2006 250. No C clamp.

Aug 03, 2010 | 1995 Ford F250

1 Answer

How do you replace the rear brakes on a 2001 Ford F250


First, get a set of brake shoes.
Second pull off wheels on both sides then remove the brake drums on both sides.
On one side pull off brake shoes springs clamps ect.
Using the side not dissasembled as an example, use it as a reference while assembling the side apart. Then pull apart the other side, and use the side reassembled to put together that side using it as a reference.
Replace drums and wheels, good luck, and give me a nice vote please.

Jul 12, 2010 | 2001 Ford F250 Super Duty Super Cab

1 Answer

Rear rotor on 2004 f250 will not come off


trere is a parking brake drum assembly attached to the rotor.you need to back off the parking brake shoes.

Sep 22, 2009 | 2004 Ford F250

1 Answer

1996 F250 Brakes


Seems regular maintenance would be required for your cable issues, and lubing them or limiting your salt water/road salt exposure and/or any underwater/extended wet exposure.
Other than replacing the mechanical section INSIDE the cab, there's nothing else that can be replaced. Besides buying a new truck. ;) Cheers.

Jun 20, 2009 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...