Question about 2004 Chrysler 300M

Open Question

2004 Chrysler 300M- Ocasionally engine turns over, but won't start -after a few minutes it starts. Ocasionally engine stops while normal driving. Again after a few minutes it will start. Have replaced oxygen sensors, had fuel ejectors cleaned, timing sensor replaced. Engine light stays on.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: Chrysler LHS o2 sensor testing

If u know u have a bad o2. I guess u must have used a scanner or equivalent. There are 4 o2s on LHS. The way u can tell the difference is by the # sequence that the failure code is giving u. For example the o2s on the right side are even # on the left odd #. Pre cat is 1 after cat is 2. So if u have bad 2/2 Than u know it's right rear or a bad 1/1 is left front ect ect. First make sure u have the right code. With out a scanner. it can be done with a volt meter or a vantage, but it's a heck of a lot easier pulling the codes.

Posted on May 15, 2008

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

on the engine where is the camshaft position sensor located

Posted on May 17, 2009

pippall
  • 1486 Answers

SOURCE: 2003 chrysler 300m o2 sensor and camshaft position sensor

SOUNDS LIKE YOU HAVE CAMSHAFT DAMAGE.

Posted on May 30, 2009

ZJLimited
  • 17970 Answers

SOURCE: how many oxygen sensors in a 2001 chrysler sebring

17c3292.jpg

Fig. Heated Oxygen (HO2S) location (sensor 1)-2.4L engine

db6f426.jpg

Fig. Heated Oxygen (HO2S) location (sensor 2)-2.4L engine

99e413c.jpg

Fig. Heated Oxygen (HO2S) location (bank 1, sensor 2) (bank 2, sensor 2)-2.7L engine

e2a250f.jpg

Fig. Heated Oxygen (HO2S) location (bank 2, sensor 1)-2.7L engine

I hope help you with this (rated this help). Good luck.

Posted on Sep 09, 2009

01fordeb
  • 1033 Answers

SOURCE: oil sending unit on 2004 chrysler sebring V6

Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chrysler 300m oil light came on while driving and the engine then shut down. the oil light is still on the dash and the car wont start. turns over fine just dont run


Are you SURE that it was Oil Light then Engine Shut off? There is not a ENGINE SHUT OFF if the light comes on that I am aware of and I have worked on quite a few 300's.

I would be trying to start the vehicle by:
Verify Fuel Pressure
Spray Starting Fluid in the Intake and see if it starts then
Are you sure there is Spark?
CRANKSHAFT SENSOR went bad

Feb 13, 2014 | 2000 Chrysler 300M

1 Answer

My 99 300m is overheating but the tempature gauge shows normal


i have a grand voyager 1999 and it temputure is running on the 3quater mark on the gauge is this right....

Jun 07, 2010 | 1999 Chrysler 300M

2 Answers

2004 chrysler 300M when I first start it up it has a ticking noise then it goes away what is it.


I have a 2004 Chrysler 300M that makes the ticking noise when first started . . . if you turn the heater control to completely off the noise stops . . .leave it off for about 3 to 5 minutes and then turn it on and it will be gone. . . my chrysler dealer repair service manager can't understand it and didn't believe me when I told him. They tried to tell me it was my motor mounts. My 18 year old daughter figured it out. go figure!!!

Nov 14, 2009 | 2004 Chrysler 300M

1 Answer

Chrysler 3.5 won`t rev past 2500 rpm?


remove the aircleaner intake hose and, check the intake air control flap for free movement

Apr 22, 2009 | 2002 Chrysler 300M

2 Answers

2002 Chrysler 300M Special, 3.5


You need to bleed the Cooling system(While engine is on...) through the bleeder valve on top of the engine (w/ heater selected ON,and on High Speed ofcourse!).

Apr 05, 2009 | 2002 Chrysler 300M

1 Answer

1999 chrysler 300m stalls when coming to stop and low power


Change the Cam Position Sensor.. It done the same thing on mine. The sensor runs about
40. to 60.00 at most parts stores Your gonna have to take off the upper intake or plenum to
get access to it. Top of the engine right side, you'll see it

Nov 28, 2008 | 2004 Chrysler 300M

1 Answer

Just shuts off...problem continues


my mom has a 99 durango that did the same thing it would just stop running and would turn over but wouldnt start let it sit for a while then it would start right up it turned out to be the brain of the car the ecu dont know if this will help but its worth a shot

Sep 02, 2008 | 1999 Chrysler 300M

Not finding what you are looking for?
2004 Chrysler 300M Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...