Question about 2004 Toyota Camry

1 Answer

Windshield washer will not work. When I opened the hood in upright the washers work. When I close the hood they will not work.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Is the hose getting pinched?

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

7 Answers

How do I add wiper fluid to my car?


Hello. Usually when you raise your hood look to the left or over to the passenger side against the side wall there will be a blue cap covering the washer fluid tank remove it fill the the tank and snap the lid back into place.

Nov 13, 2015 | Honda CRV Cars & Trucks

2 Answers

Windsheild washer motor will not work.


Windshield Washer Pump

1990 Ford Truck F150 1/2 ton P/U 2WD 5.0L FI 8cyl

The Windshield Washer Pump is located: Under hood, driver side front side of wheelwell, mounted inside washer bottle.here's the part. TAAP Windshield Washer Pump 7 664 1990 Ford F150 1 2 ton 2WD 8...

Jan 14, 2014 | 1990 Ford F150

2 Answers

THE WINDSHIELD WIPER FLUID DISPENSER ISN'T WORKING, AND THE PROBLEM ISN'T WITH THE PUMP. I HAVE BEEN TOLD THAT THE COMPUTER IN THE CAR HANDLES THIS FUNCTION AND THE COMPUTER HAS TO BE REPLACED. DOES THIS...


if you can hear the pump running when you hit the washer control you may have either a crimped hose somewhere or the spray nozzles may be clogged .also you might have a clogged hose . try the sprayer with the hood open and if it works , your hose is folding when you close the hood . if it still doesn't work , with hood open , dis-connect the hose at the sprayer . if washer fluid is coming out you can clear out the nozzles with a piece of fine wire .

Mar 09, 2011 | 1995 Mercury Grand Marquis

2 Answers

Where is the windshield washer motor?


it is connected to the bottom of the windshield washer reservoir... under the hood.

Sep 29, 2010 | 1997 Toyota Celica

2 Answers

My 96 Jeep GC windshield washer isn't squirting. I can hear it run when pushing the washer button and I hear fluid running ; but it doesn't spray on the windshield. Also , my wiper blade in the rear window...


your rear wiper motor might be faulty,in the front i would check your fluid level-if it is full and you hear the pump running-check your washer lines to see if they are pinched-usually around where the hood closes

Feb 17, 2010 | 1996 Jeep Grand Cherokee

2 Answers

Windshield washer will not squirt


Make sure you have water or windshield wiper fluid in the reserve (open your hood and add more, look for a blue plastic cap) if you hear it humming when you turn it on then the pump is working. Also check the little nozzles on the hood (one on each side) and see if they are clogged, stick a small safety pin into the holes and move it in and out to free up ant debris inside that may stop the water from squirting out

Nov 19, 2009 | 2008 Chevrolet Equinox

1 Answer

Bad wiper motor on 1996 dodge grand caravan


According to the Haynes repair manual Chapter 12:

1. Disconnect the negative battery cable
2. Detach washer hoses, lift the wiper arm covers and mark the wiper arm locations on the pivot shaft for later re-installation. Remove the wiper pivot nut and remove the wiper arms.
3. Remove the cowl cover (from chapter 11)
3a. Remove the wiper arms then remove the screws that hold the lower area of the cowl cover to the wiper module.
3b. Disengage the quarter turn fasteners that hold the outer ends of the cowl cover to the wiper module.
3c. Open the hood and release the wing nuts that hold the front of the cowl cover to the wiper module.
3d. Close the hood but do not latch it. Now remove the outboard screws and lift the cover up enough to get to the washer hose.
3e. Disconnect the washer hose from the right washer nozzle. Close the hood but do not latch it. Lift the cowl cover toward the windshield and off the vehicle.
3f. Installation is the reverse of removal
4.Open the hood. Disconnect the wiper motor electrical connector.
5. Disconnect the windshield washer hose from the coupling inside the unit. Disconnect the drain tubes from the bottom of the wiper unit.
6. Remove the wiper unit mounting bolts. (Picture appears to be three (possibly allen head) bolts)
7. Remove wiper unit.
8. Installation is the reverse of removal. Wiper blade and wiper arm adjustment is measured with the wipers parked; correct adjustment is the lower wiper arm approximately 1.5 inches distance from the cowl cover and the upper arm approximately 2.5 inches from the lower arm. Operate the wiper motor and check that the wiper motor parks when the wiper switch is OFF.

Mar 21, 2009 | 1996 Dodge Grand Caravan

1 Answer

Need to remove windshield washer resevoir


If you here the pump working check the hose to windshield to see it was pinched when closins the hood .I fixed mine wih black electrical tape and it works fine for now.

Mar 07, 2009 | 2001 Ford Taurus

2 Answers

Hi can you tell me where to find the rear windshield washer container to fill on a 99 gmc jimmy


I'm pretty sure it's the same as the front washer, You can check by see ing if there are two pumps in the front washer resevoir, if not there is a possiblity that there is a bottle in the back, servicable by opening the rear door and looking at the walls behind the tires. I hope this helps

Jan 18, 2009 | GMC Jimmy Cars & Trucks

Not finding what you are looking for?
2004 Toyota Camry Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...