Question about 2000 Nissan Maxima

1 Answer

Nissan maxima96 m/t wont start new fuel pump new spark plug ckp not showing cranking rpm when cranking scanner get off,big sound comes under the vehicle a bang

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try and replace the Crank sensor

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 nissan x terra. spins over, wont start. replaced fuel pump assembly, crank sensor, left side cam sensor. not getting any cranking rpm from scanner. HELP !


This already sounds all kinds of bad.
Lets start with spark. Did you verify it can make 30kv at all plugs while cranking? f you havent...start there. Do you have any codes in any modules? Engine, theft, trans, body?
Do you have vacuum cranking, do you have MAF reading cranking? do we know if its mechanically still in time? Did you do a cranking compression test? If you have spark, and you remove the fuel pump relay...does it start when it isnt flooding? What is your system and reference voltage...what is cranking vacuum? And what tests did you run that inspired changing all that stuff? Check the c ranking rpm in Generic mode just rpm onscreen, some OEM software doesnt update well during cranking, with one pid selected, solus should update better than 10x a sec, If you still have no signal...you need to measure the crank sensor wires or verify the crank sensor ring is even turning,

Jan 05, 2015 | 2006 Nissan Xterra

2 Answers

96 tahoe turns over but wont start 1/2 tank of gas carbs clean gas gets to carb but i got no spark I just change the distributor' coil the MAP sensor new plugs and wires last November and really haven't...


Did you visually check for spark at the spark plugs, engine cranking? Does the dist rotor turn when you crank it? Did you use a gage and check correct fuel pressure? Any applicable trouble codes? To check codes, yourself, at the least, you need an obd2 code reader.

If you have the spider fuel system, that system is noted for problems. No, the fuel system shouldn't cause a no spark. If no rpm signal, that will usually stop the injector pulse along with other issues.

Dec 12, 2014 | 1996 Chevrolet Tahoe

1 Answer

3006 chevy trailblazer turns over but wont start


That year has not been made yet and we wil be dead if and when it is. 2006 trailblazer could be fuel pump, do a fuel pressure test. CKP sensor scan for rpm, check for codes. Does it crank fast or slow? Try taking a hammer and hit the bottom of the fuel tank while someone turns th key and makes it crank. If it starts replace the fuel pump. See if it is getting spark at plugs by taking a screwdriver and insert in plug wire after you remove from plug and hold just enough away from a metal bracket and have someone turn the key to start and see if you have spark. Do not touch metal part of screwdriver.

Jul 06, 2014 | 2006 Chevrolet Trailblazer

1 Answer

Suzuki Aerio 2004, will crank over floods out tho. Changed Plugs and Boots. New baterry too. Can smell gas @ Tail pipe. Wants to fire-but just won't catch. Where do I start looking for the answers.?


what engine? 2.3 or 2.5L?
all cylinders flooding??? spark tips on ALL dripping in gas?
check spark at all spark plugs ( ALL not just ONE)
if spark is good.
this engine is chain cam, so it makes huge noise before death.
did it?, nah
ok, so connect any $9 scan tool, and scan it. (barrow /rent.?)

you crank it for 5 seconds, not less.
and as you crank the scan tool RPM shows 250 to300 rpm and fails to start, the RPM on the tool shows you that the crank sensor is working
now release the key and do not turn off
look for DTC errors. got P0340,355? or any other DTC
that decodes to bad CMP or CKP/
yes, BINGO, the scan tool told you why spark is dead, or way off
timing,

the PCM will report Cmp or CKP errors even 1 in 6 pulses.
the PCM runs monitors against these 2 full time. and will see it fail.
and report, it, let it tell why spark is bad.
say spark is good. and still floods.
1: engine compresssion over 150psi? W.O.T?
2: flooding , i pull the fuel pump relay and crank now.
starts and runs for 3 -5 seconds, yes, that is the flood clearing
so i then try test fuel, runs perfect now (no fuel pump) ???
runs for 3 second, each test fuel usage. well good motor, good spark.
what more do you want? sure to run
so you have either insane high fuel pressure. or injectors leaking
can and does happen.
the tests are all in the FSM under injector and pump testing.
i check fuel pressure first. as its a mandatory thing.....
to factory spec. for unsaid engine.
then i do a injector leak down and balance check.
ask if you get this far.....????


Jan 24, 2014 | 2004 Suzuki Aerio

1 Answer

1999 Gmc Sierra 4.8L cranks/No Start Using snap-on Solus Scanner. I followed basic diagnostics: Checked fuses- good Pulled PCM and BCM codes- none No spark and no fuel. No ignition power to fuel...


Did you check your CKP and CMP power wires for a short to ground? Short to ground up stream might be pulling the voltage low from the PCM. Also.. have you pulled up the underhood fuse block just to see if there's any rodent damage to the wiring under there? That's a pretty common spot for rodents to cause problems.

Oct 03, 2013 | Cars & Trucks

1 Answer

Car cranks but no start


no year or model, really?
ok ill answer for a Generic car (hopeless)
1: no spark and all EFI systems kill fueling at the detection of no spark (stopping the burning fire, and 911 call,etc.....)
i must stop, no year, wow.
if car is 1996, and newer my answer would be....
check all fuses in cab and engine bay for blown.
scan - all newer cars the scan tool is $9 (ask) or fleabay it your self.

spark , no engine option stated, must i guess it all? wow.
but each year, generation has newer spark designs.
totally radically different by GEN.
ok if its a 96"
the scan tools shows zero rpm cranking, and maybe code, 340 or 355, if yes, the Ckp is bad with zero rpm, in fact RPM IS CKP.
CKP means crank position sensor.
some engine, (lots) can die with a CMP dead.
CMP is the Cam angle sensors. (some, not all)
the FSM covers no spark , why not read it.
go to
alldata.com and see it all .
or post car spec, and we can post EXACT answers.
not possible now..

Sep 25, 2013 | Honda Cars & Trucks

1 Answer

I have 2005 Nissan altima that wont start. It cranks but wont start. I checked the battery with a portable load tester, good. No codes or check engine light. Fuel pump pumps fuel, wont even come on with...


Nissans are known to have problems with ignition coils which would not show up on code reader. I would start with that. Pull a plug and hold it to ground to see how strong the spark is while turning engine over. If the plugs are wet when you take them out then you can be sure it is in all probability related to coils.

Nov 24, 2010 | 2005 Nissan Altima

1 Answer

2001 Nissan Sentra cranks but wont start. Put a


good day Sir, try to check the spark plugs and air filter, i hope this tips will help you.

May 25, 2010 | 2002 Nissan Sentra

1 Answer

Engine cranks but wont start


Usually if no rpm signal, the vehicle won't start. Engine cranking, did you check for spark at the spark plugs? The fuel pressure you listed may have been the initial prime. It sounds like no injector pulse. The rpm signal comes from crank sensor. If your missing rpm signal, may thought is the crank sensor.
Were there any applicable trouble codes?

Apr 06, 2017 | 2001 Ford F150 Styleside SuperCrew

1 Answer

1993 nissan sentra sparkplugs are getting wet car wont start


Your timing chain may need replaced.
Sounds like your plugs are sparking too late or too early.
or the gap is too big in your plugs. ( get a gapper and regap to .08 ish.. )
Try these

Sep 10, 2008 | 1993 Nissan Sentra 4 Door

Not finding what you are looking for?
2000 Nissan Maxima Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...