Question about 1997 Isuzu Rodeo

Open Question

HOW MANY GALLONS OF COOLANT IN RADIATOR - 1997 Isuzu Rodeo

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How much antifreeze do a 2000 ford expedition takes


5 gallons of fluid irrespective of how it is mixed. I answered this earlier for you didn't I with links to specs and videos of how to do it?

Spooky, it wasn't you! Look at this link there is lots of info.
http://www.fixya.com/cars/t26226280-many_gallons_antifreeze_goes_in_2002

Jun 26, 2016 | 2000 Ford Expedition

Tip

Flush the coolant on the 2002 tundra


PROCEDURE TO FLUSH
  • Park the Toyota Tundra on a level surface and set the parking brake. Then, with the engine off, touch the radiator to gauge its temperature. If the radiator is still warm, allow it to cool off before you start next step.
  • Twist the radiator cap one full turn, pause for a few seconds and then fully remove the cap. You want to pause to relieve any internal pressure inside the radiator. Opening a pressurized or hot radiator can cause it to spew hot coolant and burn anyone it comes into contact with.
  • Position a bucket or tray with a two-gallon capacity underneath the radiator, below the drain plug. To access the drain plug, you may have to remove the plastic engine undercover, which should be on the driver's side of the Toyota Tundra's radiator. Use a socket wrench to open the plug.
  • Open the drain plug and allow the existing coolant to drain completely into the bucket. Once complete, pour the old coolant into a sealable container for proper disposal.
  • Put the drain bucket back under the radiator and close the drain plug. Then, fill the radiator with distilled water. Next, open the drain plug to let the water flow into the bucket. Replicate this procedure until the water runs debris free out the radiator.
  • Replace the radiator drain plug and pour fresh coolant into the radiator until it's within an inch of overflowing. With the Toyota Tundra, you need to use the same coolant that came with the truck. Most likely, it is Toyota Long Life red coolant, but consult the owner's manual to be sure.
  • Start the engine of the Tundra and turn the heating fan to high. Allow it to run until the cooling fan turns on two separate times.
  • Switch the Toyato Tundra off and check the coolant level. If it is lower than before, add more coolant. If not, put the radiator cap back on and close the hood.
TIPS
  • You will need 2 gallons of coolant for the four-valve Toyota Tundra and 3 gallons of coolant for the six-valve model.
  • Using tap water from a hose is an alternative to flushing with distilled water, but tap water can leave sediments behind that can damage your coolant system
WARNING
  • Because coolant is extremely toxic to people and pets, it's imperative that you dispose of the old coolant properly.

on Mar 17, 2010 | Toyota Tundra Cars & Trucks

2 Answers

Im trying to replace my coolant and I'm not sure how much to put in. It's the 4.3 L v6 in a 1988 GMC c1500


Don't know the exact amount but around 2-2 and a half gallon. Do this use one gallon straight antifreeze and one gallon water run engine for a few minutes then turn off. Check level and top off radiator. Add appropriate level to side tank

Apr 25, 2016 | GMC Cars & Trucks

1 Answer

How many gallons of coolant does the northstar engine hold?


Coolant should be mixed in most cases to a 50% concentration, meaning one gallon of undiluted coolant will provide two gallons of diluted coolant. Most engines will hold 2-3 gallons of coolant mix. I normally purchase two gallons of undiluted coolant. I pour the first gallon of undiluted coolant into the radiator, then fill the empty bottle with water and add that to the radiator as well to make it a 50% mix.. Then, I pour half the second bottle of undiluted coolant into the empty coolant bottle, and then top both off with water to make two gallons of 50% mix. I then add coolant to the radiator as needed until full, keeping the remainder for topping off later as air purges itself form the system.

Sep 04, 2014 | 1997 Cadillac DeVille

1 Answer

How many gallons needed to replace coolant from radiator on 2004 Chevy Tahoe 5.3L


About 3 and 1/2. If you let it set and drain. Takes time. If you drianed just the radiator and what spills out. Maybe 2 gallons.

Mar 14, 2014 | 2004 Chevrolet Tahoe

1 Answer

How to flush coolant on 2004 grand prix


  • Move your badass w-body (a.k.a. Pontiac Grand Prix) to a level area and set the parking brake. Pop the hood and touch the radiator. If it's warm let it cool before you continue.
  • Twist the radiator cap one full turn (Remember to be careful because even when radiators are cool they can still erupt coolant)
  • Place any type of container (bucket [but has to be able to hold 2 gallons]) underneath the radiator and blow the drain plug. (The drain plug on your Grand Prix is on the driver's side bottom of the radiator facing the engine.)
  • Loosen the drain plug and let the old coolant to drain completely. (You may need a wrench to loosen the drain plug)
  • Dispose the old coolant in a sealable container (The coolant is very toxic to people and pets, so you gotta be careful)
  • Shut the radiator drain plug and fill the radiator with water.
  • Run car for a little bit and repeat the process again. (Let car cool, and drain water)
  • Close the drain plug and fill the radiator with fresh coolant until it's about an inch from overflowing. (DO NOT USE ORANGE DEX COOLANT IT IS HARMFUL FOR YOUR HEADGAKETS) You will need 3 gallons of coolant (SE, GT, GT1, GT2, GTP, GTP Comp G.) and 4 for the GXP model. Be sure to check the drain plug for any leakage.
  • Start your car and turn the heating system to high. Allow the car to keep running until the cooling fan turns on twice. After that happens, switch off the engine and check the coolant level. If it went down, add more coolant. If not, put the radiator cap back on and close the hood.

Feb 20, 2014 | Cars & Trucks

1 Answer

How much coolant will it take to replace after flushung radiator on 2007 chevy impala


normally 2-3 gallons if you use the premixed 50/50 coolant, if you use straight coolant you will need to mix 50/50 with distilled water. the cooling system will hold approximately 3 gallons of coolant total

Mar 24, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

How much coolent in 1996 mercury mastique I live in florida just flushed rad


Use a rule of thumb,with a empty radiator add one gallon coolant and the rest water,if you want to add more coolant go ahead,its when there is not enough coolant or just plain water is where the problem begins,1 radiator 1 gallon coolant or even more.

Aug 07, 2012 | 1996 Mercury Mystique

2 Answers

How do I flush the coolant on the 2002 tundra V6?


PROCEDURE TO FLUSH
  • Park the Toyota Tundra on a level surface and set the parking brake. Then, with the engine off, touch the radiator to gauge its temperature. If the radiator is still warm, allow it to cool off before you start next step.
  • Twist the radiator cap one full turn, pause for a few seconds and then fully remove the cap. You want to pause to relieve any internal pressure inside the radiator. Opening a pressurized or hot radiator can cause it to spew hot coolant and burn anyone it comes into contact with.
  • Position a bucket or tray with a two-gallon capacity underneath the radiator, below the drain plug. To access the drain plug, you may have to remove the plastic engine undercover, which should be on the driver's side of the Toyota Tundra's radiator. Use a socket wrench to open the plug.
  • Open the drain plug and allow the existing coolant to drain completely into the bucket. Once complete, pour the old coolant into a sealable container for proper disposal.
  • Put the drain bucket back under the radiator and close the drain plug. Then, fill the radiator with distilled water. Next, open the drain plug to let the water flow into the bucket. Replicate this procedure until the water runs debris free out the radiator.
  • Replace the radiator drain plug and pour fresh coolant into the radiator until it's within an inch of overflowing. With the Toyota Tundra, you need to use the same coolant that came with the truck. Most likely, it is Toyota Long Life red coolant, but consult the owner's manual to be sure.
  • Start the engine of the Tundra and turn the heating fan to high. Allow it to run until the cooling fan turns on two separate times.
  • Switch the Toyato Tundra off and check the coolant level. If it is lower than before, add more coolant. If not, put the radiator cap back on and close the hood.
  1. TIPS
  • You will need 2 gallons of coolant for the four-valve Toyota Tundra and 3 gallons of coolant for the six-valve model.
  • Using tap water from a hose is an alternative to flushing with distilled water, but tap water can leave sediments behind that can damage your coolant system
WARNING
  • Because coolant is extremely toxic to people and pets, it's imperative that you dispose of the old coolant properly.

Nov 14, 2009 | 2002 Toyota Tundra

1 Answer

Heater not working


The Navigator has rear air, so coolant lines run to a heater core in the rear. It will help if you elevate the front of the truck on a set of ramps or incline. Turn the heat for both front and rear. Run the truck and add coolant as needed until all the bubbles come out of the coolant tank. You can tell when you get coolant to the rear when hot air blows from the vents. By raising the front of the truck you allow the the air in the lines to bleed to the front.

Jun 22, 2009 | 2001 Lincoln Navigator

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...