Question about 2000 Chevrolet S-10

Open Question

Where are all the air bag sensors located on my 2000 chevy s10 ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: I need a wire diagram for a 2000 zr2 s10 chevy 4x4

  1. this should help.8d4efbb.gif

Posted on Aug 07, 2009

Ad
  • 14036 Answers

SOURCE: Trying to find location of air bag crash sensors

THE AIR BAG CONTROL MODULE IS ON THE FLOOR AHEAD OF THE CONSOLE.BECAREFUL YOU CAN CAUSE AIR BAGS EMPLOYMENT ACCIDENTALLY.THEY ARE DANGEROUS.THE DEALERSHIP HAS TO RETRIEVE AIR BAG FAULT CODE.

Posted on Aug 30, 2009

techbuster
  • 5081 Answers

SOURCE: location of crankshaft sensor on a 98 chevy s10

It is located on the passenger side of the engine block just under the ignition module you can see it from underside. The easiest way to see it and access it is to jack up the passenger side front wheel and take the wheel off there is a rubber flap in the wheel well you can push out of your way. I am warning you be very careful removing it mostly made of plastic I broke one off leaving most of the sensor in the engine block had to drill the rest of it out which was no fun not alot of room for you to work. Get yourself a bottle of PB Blaster and keep spraying it as your pulling out before you try pulling out the sensor try to get it free enough that you can spin it around. Hope this helps good luck it fits pretty tight!

Posted on Oct 30, 2009

  • 617 Answers

SOURCE: Location of mass air flow sensor, 2000 Grand Prix GTP

3.1 or 3.8 motor, mass air flow is in the fresh air (goes from air cleaner to engine)

Posted on Feb 07, 2010

  • 118 Answers

SOURCE: 1994 chevy S10 where is the crank sensor located

If you have the vortec engine the sensor is located on the passanger side of the engine just above the oil pan at the front of the engine. It goes through the block and has one single 10 mm bolt through the retainer. Be careful removing it from the block as years of corrosion can cause it to get stuck and you can break it off in the block.

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the air bag location?


If the air bag light is on there is a code stored in the SRS restraint module - air bags ! Wiring problem , impact sensor ! First place to start is have the vehicle check for codes . Not with OBD2 code reader., factory or professional grade scan tool . If you have not worked on air bag systems I recommend you take it to a ASE certified repair shop or the dealer . People have been killed by accidental air bag deployment , by not knowing what's up . Takes special tools !

Dec 28, 2015 | 2000 Pontiac Bonneville

1 Answer

Where are the passenger side air bag sensors located on a 2009 chevy impala?


Side Impact Sensor (SIS)--Located behind door panel on the passenger front door
Front End Sensor--Located under the hood at the front right side of the vehicle
They have yellow wires going to them !

Jan 12, 2015 | 2009 Chevrolet Impala

1 Answer

Where is the ac low pressure port located on a 2000 chevy s10?


It's the port on the accumulator. The silver tank attached to your fan box. The low side of your a/c system is always going to be the larger hose.

Jun 17, 2014 | 2000 Chevrolet S-10

1 Answer

Where is the cabin air filter for a 2003 chevy s10


The 2003 S10 does not have a cabin air filter.

Mar 20, 2013 | 2003 Chevrolet S-10

1 Answer

How do I find the blower resistor on a 2000 chevy S10 pickup


Here's what it look's like,it's located next to blower motor,remove electrical connector and two screws and ala,it's off.

Jan 31, 2013 | Cars & Trucks

1 Answer

Where is the temperature sending unit located on a 2000 chevy s10 2.2 four cylinder engine


The temperature sending unit is screwed into cylinder head. Careful you also have a coolant temperature sensor that threads into intake manifold. Temp sending unit is how your guage knows how hot your engine is. Coolant temp sensor is how your computer knows how hot or cold your engine is, so it can compensate fuel & air mixture.You can not put the wrong one in the wrong place, they will not fit. You change 1 for 1 reason & the other for another reason.

Jun 16, 2010 | 2000 Chevrolet S-10

2 Answers

2000 chevy s10 starts fine but dies out when push


Have you changed the fuel filter lately? If not do so. Sounds like fuel restriction. Filter usually on frame rail passenger side. Good luck!

Apr 13, 2010 | 2000 Chevrolet S-10

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...