Question about 1994 Chevrolet C1500

1 Answer

Have a 94' chevy pickup. When I press on brake pedal, left front always grabs 1st, then left, but it stops the truck. Rotors & pads are in good shape. Had differential valve replaced about 2-1/2 yrs ago. Was having same type problem then, but got better. Now it is doing the same thing. Pedal does not go to floor but seems to have too much travel when you press down on it . Any suggestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 7,772 Answers

Flush the system and look for contaminants. If there is a bleed on the proportioning valve, also flush there. If there are contaminants, your master may need to be replaced. If not, maybe the proportioning valve has failed again.

Posted on Aug 04, 2017

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Brakes no longer work in 1989 Chevy half ton pickup 2 wheel drive 350cubic inch

change dump valve under master cylinder

Posted on Aug 17, 2008

  • 131 Answers

SOURCE: I had the front disk brake pads and rotors

check you fluid brake fluid level, and rebleed the system. that should help it out, sounds like you may have air in the line.hope this helps

Posted on Aug 14, 2009

jayhawke
  • 338 Answers

SOURCE: Rear brakes not working proper.

e-brake pedal should go farther- is either out of adjustment or cable frozen- secondly sounds like only front brakes receiving enough pressure to "activate" properly- bleed all four brakes starting rear pass,then rear drive ,then front pass, then front drive- use plenty of fluid- bleed till fluid is clean without bubbles- will that long at first- this will insure not bubbles and no moisture- if a pro valve dies,you would have more problems- pedal would be really soft,would have both a brake light and abs warning lights

Posted on May 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why do my brakes vibrate when I'm stopping?


Your brake rotors are warped and need to either be shaved or replaced.

Apr 04, 2016 | Cars & Trucks

1 Answer

I had new pads installed on the front of my 2005 chevy equinox, the rotors were turned and it stops perfectly execpt the front right wheel always squeaks and is geting worse even though I used the 20/30...


I personally never have had one braking issue, in 47 years
of doing brake work,on any vehicles

That said & not to write book here

The brake work & choice of friction material
(brake pads) was not done correctly

Very few shops remove rust from anything
Rotor mounting surfaces,wheel hub surfaces,
calipers,caliper sliding surfaces,pad siding surfaces

Then they use no lube, so pads can move & release

They don't use MFG Specific & quality pads

A proper professional job would go for at least
$300.00 for front or back,just 2 wheels

Rotor machining is critical

I think your OEM Rotors that were machined, most likely
were okey new & not a good grade of Chinese Steel to
be machining

Aug 03, 2011 | 2005 Chevrolet Equinox

1 Answer

When the anti lock brake light on my 93 lincoln town car comes on, if I am pressing on the brake at the time, makes the brakes grab. It also happens just before the light comes on. I have had the front and...


the abs light on the dash should come on when the abs is working (emergency braking)if it comes on when braking normally(gently)chances are a sensor is gone(replace in pairs,fronts & rears)
abs stops the wheels from locking up in an emergency brake situation,you will feel the grab-release,grab-release on the brake pedal......

Jul 16, 2010 | 1993 Lincoln Town Car

1 Answer

I own a 2007 Chevy Malibu LS. Recently my brakes have been 'squealing' and my steering wheel has always vibrated when I press on the brake. I thought it was my brake pads and rotors but I just had them...


checked out replace pads /and cut rotors if pads are glazed over [film u were told ] the pads are smoothed over from getting to hot -riding brake or stop and go traffic lot of down hill braking which ever was the cause ur brakes got over heated and glazed over and are very smooth also the heat transferred to the rotors also warped them when u get steering shake when braking 90 percent of the time its warpage in rotor and the only way is to have them removed and put on a cutter to check for out of round also abs doesnt cause this abs [anti-lock braking] is designed to transmit a pulse to ur brakes when it senses a wheel is about to lock up or skid u would feel the pulse in ur brake pedal not ur steering

May 23, 2010 | 2007 Chevrolet Malibu SS Sedan New Cars

2 Answers

I just replaced my front rotors, pads, and calipers on a 98 olds achieva. After doing this I bled the the front brakes but am now experiencing a very soft pedal. I am wondering if something else could be...


Because of the ABS system if you press the brake pedal with too much pressure then it will give you the illusion of a soft pedal. Does it feel like a soft pedal when the vehical is in motion and you then press on the brake pedal (normal)? The other thing is if your pads and/or caliper were frozen, when you changed them out. The brakes are not going to feel or brake exactly the same, after the repair. But you are there, if the pedal is real low or goes to the floor then there is still air in the system or for some reason, your master cylinder is defective.

Jun 18, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Toyota sr5 brakes slip


Did you adjust the rear brakes?

Nov 10, 2008 | 1989 Toyota Pickup SR5

Not finding what you are looking for?
1994 Chevrolet C1500 Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...