Question about 2005 Chrysler PT Cruiser

1 Answer

I need to know where the Cam Shaft sensor is for my 2005 PT Cruiser is. My car is sputtering and the car is not starting when the switch is turn on.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

The cam sensor is near the battery. it is on the end of the cylinder head rear. you should have a code po340 if the cam sensor is bad. get someone to scan it before replacing the sensor . check under the car for a wire rubbing on the cv shaft that goes to the crank sensor.

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pt cruiser cranks but won't start


Did you check to see if there is a neutral safety switch on the transmission?

Feb 02, 2014 | 2006 Chrysler PT Cruiser

1 Answer

Change cam and crankshaft sensor for pt cruiser 2005 and still in the diagnostic problem cam sensor


just remove the battery terminals for a while firstly removing negative terminal

Sep 17, 2013 | 2005 Chrysler PT Cruiser

1 Answer

2005 PT Cruiser fuel gauge is wrong suddenly. Put gas in and still shows empty


2005 PT cruiser, i replaced the cam sensor with a aft market sensor my fuel gauge started reading wrong, and it didn't fix my problem so i replaced the cam sensor with a factory sensor it fix my running problem but the fuel gauge still reads wrong, with a full tank of gas the gauge reads 3/4 tank,

Feb 28, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

How do I replace a 2005 pt cruiser camshaft sensor


Camshaft sensor sit in the end of the cylinder head, drives side, just unscrew both little bolt's from sensor, remove sensor, and install new cam sensor, no reprogramming needs to be done.

Sep 09, 2010 | 2005 Chrysler PT Cruiser

2 Answers

Car is jerking and the engine has come on but it has oil and transmission fluid in it


We had an issue with our 2005 PT Cruiser. The check engine light came on and had trouble starting. Once it did start it would buck and sputter. I did some research on the web and found similar problems. From what i found it is the cam shaft sensor. This happened yesterday. We are getting it checked today. I won't go as far as to tell you this is exactly what it is, but it is a good place to start. Hope this helps!

Aug 12, 2010 | 2004 Chrysler PT Cruiser

1 Answer

Engine died at hwy speed crank/cam sensor faults


o1 cruiser spit and sputter go down rd put cam sensor and crank shaft sensor on wouldnt run at alll with new crank sensor had to put old one on please hel

Sep 29, 2009 | 2004 Chrysler PT Cruiser

2 Answers

Sputtering on accelerations


If no check engine light is on, I would try to replace the coil pack first. Usually on these cars a drop in fuel pressure associated with a bad fuel pump should throw a code.

Jul 10, 2009 | 2005 Chrysler PT Cruiser

3 Answers

Spit and sputter/2004 PT Cruiser


Check for fire to the coil pack. These have a tendency to go bad on these cars. Could be a cam or crank sensor, these also go bad. If you haven't changed the plugs in 30K, this is due also, wires every 60K. May need to actually get it hooked to a machine to find out for sure.

Jun 02, 2009 | 2004 Chrysler PT Cruiser

2 Answers

2001 PT Cruiser quit running driving down highway


Most likely a cam sensor or a crank sensor. The timing belt didn't break did it? They also have an issue with the timing belt tensioner going bad and jumping a tooth.

Mar 05, 2009 | 2001 Chrysler PT Cruiser

2 Answers

2003 pt cruiser sensors


check the battery and make sure it has a fully charge,also check to make sure the start motor pinion is not jammed in the flywheel, and check the coil pack to make sure have spark.also check the crank sensor

Feb 14, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

477 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...