Question about 1995 Honda Civic

1 Answer

How many bolts are on tha starter for 1995 honda civic

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! There are two bolts that holds the starter. You will need a 14mm wrench or socket to loosen them. Hope this helps and thank you for using FixYa!

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lotate the filler bolt on a 19995 Honda civic manual transmission


17 mm bolt on side, near back of trans, by diff.

Feb 17, 2013 | 1995 Honda Civic

3 Answers

Where i can find the starter for honda civic dx 2008?


The starter should be located on the left side of the engine. That is the side nearest the front of the car. Typically the transaxle spans a portion of the right side of the engine. You may also find related info on tha Autozone website. Enter your vehicle info then go to "view job diagram" on the right side of the page.

Oct 11, 2012 | 2010 Honda Civic DX

1 Answer

What are the head bolt torque settings for a 95 honda civic dx 1.4


there is not a 1.4L listed in the 1995 civic dx there is a 1.5L and a 1.6L

1.5L

D15B7 & D15B8 engines
step 1 22lbs
step 2 43lbs

D15Z1 engine

step 1 22lbs
step 2 53lbs


1.6L VTEC

step 1 22lbs
step 2 53lbs

Sep 14, 2011 | 1995 Honda Civic

1 Answer

How do you remove a power steering belt off of a 1995 honda civic ex


Loosen the 2 12mm bolts and turn the wing nut to loose it, the P/S pump should slide down, reverse to install.

Apr 03, 2011 | 1995 Honda Civic

1 Answer

Is the starter cylinoid in the starter - 2000 Honda Civic DX


No, the solenoid in bolted to the top of the starter.

Jul 20, 2010 | 2000 Honda Civic

1 Answer

I need to replace my starter on my 1993 honda civic... Help?


  1. Disconnect the negative battery terminal and the starter motor cable at the positive terminal.
  2. Remove the engine wire harness from the harness clip on the starter motor
  3. Disconnect the cable from the B terminal on the solenoid, and the BLK/WHT wire from the S terminal.
  4. Remove the starter motor by loosening the two attaching bolts.
  5. To install, reverse the removal procedures: re-position the starter in place, replace bolts, tighten the starter-to-engine bolts to 32 ft. lbs. (45 Nm).
  6. Make sure that all wires are securely connected.

Mar 20, 2010 | 1993 Honda Civic 4 Door

1 Answer

We can't get the transmission loose from the engine on a 1995 Honda Civic DL. We have tried everything we can think of; do you have any suggestions?


automatic? remove the torque convertor bolts and remove the bolt on the back front side of the engine that goes into!! the tranny from the front and its a by**h to get to stick tranny has same bolts in same place

Jan 22, 2010 | 1995 Honda Civic

1 Answer

1991 honda civic starter removal


Always start by disconnecting the battery when working with electrical parts on a vehicle. Once that is done then unplug the starter and unbolt the nut under the rubber boot which should be either 8mm or 10mm bolt, i can't remember which. Then next there will be two long 12mm or 14mm bolts holding the starter to the trans...remove them and the starter should lift right out. For installation just do the same but reverse and don't forget the metal gasket and i recommend putting di-electric grease on the electrical connections to keep those in good working order. Good luck

Oct 29, 2008 | 1991 Honda Civic

2 Answers

Replacing head gasket on 1995 honda civic, require torque specs and secquence


wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.

Sep 13, 2008 | 1995 Honda Civic

Not finding what you are looking for?
1995 Honda Civic Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...