Question about 2008 Ford Edge

Open Question

Ford edge tire pressure warning light - 2008 Ford Edge

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: LOW TIRE PRESSURE WARNING LIGHT

Turn ignition to run position,go to fuse panel right hand of vehicle,push and hold reset button for 5 seconds,low pressure light will flash 3 times,start car it should turn off the low pressure light.

Posted on Jan 29, 2009

Ad
  • 60 Answers

SOURCE: how do i reset the tire pressure warning on a 2008 kia spectra

Don't just simply have it replaced. Go to a quality tire shop that has a scan tool to verify that your sensors are working in all tires. It may simply be a leak around the grommet kit of the sensor or something in the tire causing leakage. Get it checked out before you spend money you don't need to.

Posted on Aug 16, 2009

jasonrwagner
  • 14 Answers

SOURCE: switch off tire pressure warning light

Malfunctions
As long as there is still a malfunction, the
yellow indicator lamp on the instrument
cluster will stay lit up.
The indicator lamp also lights up in the
event of a system malfunction.
Please contact your MINI center in these
cases.
Initializing the system
Only initialize the system if the inflation
pressure, e. g. after a tire change, has been
corrected.
1. Ignition key in position 2
2. Press the button long enough for the
yellow indicator lamp in the instrument
cluster to light up for a few seconds
3. Start the engine.
After a few minutes driving time, the Flat
Tire Monitor sets the current inflation pressure
in the tires as the target values to be
monitored

Posted on Jul 13, 2008

  • 4 Answers

SOURCE: Tire pressure light is on

If you have the spare on it doesen't have the sensor in it and the light will stay on. If the spare is not on then you have a bad sensor in one of the wheels.

Posted on May 02, 2009

Ajkill
  • 2035 Answers

SOURCE: low tire pressure warning light

You do this by removing the low pressures fuse from the main fuse box or you need to disconnect the sensor ......to bypass the computer.............

Posted on Jun 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Freestar Message Center not visible. Need help resetting tire warning light.


You can't reset the tire pressure warning light (TPMS), when the pressure is adjusted or the sensor replaced (if the warning is false) the light will go out, there is no reset. Check the air pressure in all the tires, they should be about 34 PSI all around.

Jun 03, 2016 | 2004 Ford Freestar

1 Answer

Tyre Pressure and ABS


By operating the tire pressure warning system reset switch, tire pressure warning system ECU can be set to issue a warning at an inflation pressure that corresponds with the type of tires.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON. When starting the initialization, the tire pressure warning light blinks 3 times at 0.5 Hz.
During the initialization, the tire pressure warning system valve & transmitter measures the inflation
pressure of the tires, and registers the signals that are transmitted into the ECU at a frequency of 1 per
minute. The initialization process is completed when the signals from the tires have been received.
Once the tire pressure warning system reset switch has been pressed, do not turn the Ignition switch OFF for a few minutes.

Mar 05, 2014 | 2002 Toyota Corolla

1 Answer

Tyre pressure warning light showing when pressures are correct


Hi, the tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You can re-initialize the system by following these steps:

1. Check and make sure that your tires are inflated to the correct pressure

2. Turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (in the glove box) until the warning light turns off and then release the switch.

3. Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. Initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

May 13, 2011 | Renault 18I Cars & Trucks

1 Answer

How do you reset the warning light


What year, make, and model Ford are you referring to? What kind of warning light are you referring to? If you are referring to a tire pressure monitor TPMS warning light, it will reset itself after the correct air pressure registers in the tire that is/was impacted, and you drive it for a couple of miles.

Mar 07, 2011 | Ford Fusion Cars & Trucks

3 Answers

"Check tire pressure" light stays


Did you check the spare tire too?

Jan 17, 2011 | 2005 Ford Freestar

2 Answers

The words tire reset keep on popping up on my dashboard. What does that mean, and how do I get rid of it? 2004 Ford Freestar.


With and without "Mesage Center" respectively (pretty sure)

With the engine on...

Push "Setup" button, until your driver display says something like "Press Reset for system check".

Then push Reset. The system check will start, rotating through a series of checks.

About the fifth or sixth check will be the tire pressure. The system will sound the tone (same one that starts w/the light) and It'll say something like "Check Tires Pressure" on that moment press and hold for 3 or 4 seconds Reset. When you release the Reset button It'll show "Hold Reset if tires are OK". While that's up, hold the Reset button. After 3 or 4 seconds, the tire warning light will blink 2 or 3 times and then will stop .You need to be ready for it, because you don't get very long to release.

How to reset the low tire pressure warning if the vehicle does not have the "Message Center"

Turn the ignition to the ON position,
depress and Trip/odometer button (located in the instrument cluster) until "TIRE RESET" or "CHECK TIRE AND RESET" is displayed in the odometer display window.
Once "TIRE RESET" or "CHECK TIRE AND RESET" is displayed, press and hold the button for three seconds.
The low tire warning indicator light will flash three times as the low tire warning system begins to initialize.

This information is in the Owners Manual

Hope it helps

Nov 04, 2010 | 2004 Ford Freestar

2 Answers

2004 Ford Explorer - dash light that looks like an upsidedown kettle with an explanation mark in the center...?


Yeah Its a tire pressure monitor. When the temperature decreases, the tire pressure light comes on if they are just a little bit low. I filled mine up to the proper PSI and it stopped the issue.

Oct 11, 2009 | 2004 Ford Explorer

1 Answer

Changed right front tire now reads zero on dash light is on


Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 24, 2009 | 2008 Chevrolet Tahoe

1 Answer

2005 ford freestar reset light on


Vehicles Without Message Center To reset the system, press and hold the odometer reset button and wait for the "TIRE PRESSURE SET" light to illuminate. Continue to press the button for 3 seconds, then release. After 3 seconds, the low tire pressure warning lamp will flash 3 times, indicating that the low tire warning system reset procedure is complete.
Vehicles With Message Center To reset the system, press and hold the SETUP button and wait for the message center to display "REST FOR SYSTEM CHECK". Then press the RESET button and wait for the message center to display "HOLD RESET TO RELEARN". Press and hold the RESET button for 3 seconds. The message "HOLD RESET TO RELEARN" and the low tire warning lamp will flash 3 times, indicating the reset procedure is complete.

Mar 12, 2009 | 2005 Ford Freestar

Not finding what you are looking for?
2008 Ford Edge Logo

Related Topics:

3,071 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...