Question about 2002 Audi TT

1 Answer

Clutch pedal appears to have dropped a little Making gear selection difficult Year 2002

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

Adjust the cable on the other end (3"long bolt with 2x nuts on yoke of clutch actuator.)

Posted on Sep 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Clutch disc and Release Bearing for the TD4-Freelander, were replaced recently. The Pressure Plate was still in a good condition.Gears difficult to engage.Please advise.Tks.John.


Most likely still has air in hydraulic clutch slave system. Many transmisions will have dificulty shifting if clutch doesn't full disengage. If air is in system it won't allow full disengage thus difficulty in shifting even possible grinding gears

Sep 17, 2016 | 2002 Land Rover Freelander

1 Answer

I have a 1991 chevy K1500 and we replaced the fly wheel and now it wont go into gear.. HELP!


the most common fault is what you have stated
clutch plate in back to front
the clutch plate hub hits on the flywheel bolt heads and the plate is still driven making 1st and reverse gears difficult to select without crunching them

Feb 29, 2016 | Cars & Trucks

1 Answer

The fork on my clutch snapped and it along with the release bearing were replaced. Clutch was very hard and pedal vibrated when touched. Gears were difficult to select as well


Hi,its always best to replace the hole of the clutch kit,as the presher plate is proberly damaged as well,all the best.

Feb 07, 2016 | Cars & Trucks

1 Answer

2001 406 diesel estate manual. 11600 miles. clutch replaced 2 years ago. normal everydare use it is all ok. recently was in heavy traffic for over 2 hrs. never out of 1st & =2nd gear. Engine temp just...


If the clutch is correctly adjusted, it will start to engage when releasing the clutch pedal at 1 in. off of the floor. When in Heavy traffic shift trans to neutral while at a stop, take your foot off of the clutch pedal to avoid overheating the release bearing

Jun 05, 2017 | Peugeot 406 Cars & Trucks

1 Answer

Hi my Suzuki wagon r+ had a clutch replacement last year and the clutch pedal is a little stiff. However i must stress all gears are usable with no noises coming from the box. I have a cable clutch and not...


When you replace the clutch it would have been a good idea to replace the clutch cable as well. The inner cable wears a groove in the outer case and this is now binding and making the pedal movement heavy. What you cannot push in easily ,the clutch cannot push back easily so there is a possibility of increased wear on the throw out bearing or slipping clutch. Replace it as soon as possible.

Sep 06, 2013 | Cars & Trucks

1 Answer

The clutch pedal at times gets soft and gear shift is hard I have to turn off the truck pump the pedal for a while, some times when it is in 4th gear is hard to gear down


I have a 92 toyota camry and had to have my clutch replaced & the switch a year ago I already know it's all hydraulic but now the clutch pedal feels spongy easy to push in I have to wait till the car warms up & the rpm's drop even in 90 degree weather & then it's still hard to shift into gear once I'm able to drive it around for a little while it seems to work fine, I called Firestone who done the clutch they said it COULD be the clutch master cylinder how could I be sure or what can I check to be sure of what it could be before I take my car anywhere to be fixed.

Jan 25, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

97 civic ex MT clutch "flops", very little resistance


check the brake and clutch fluid resiviors.
if low add dot3 brake fluid.
but if sounds like the clutch is done.
about $800 to replace .

Nov 17, 2009 | 1997 Honda Civic

1 Answer

Problem going into gear


Your clutch system works the same as brakes do. The necessity to bleed tells you that there is a malfunction permitting air into the system. Check where the pedal rod goes into the firewall under the dash, the line itself, and the slave unit (some are inside the bellhousing...look for fluid dripping from bottom to verify if leaking) Not unlike brake master, they can also internally bypass. If you find no leaks, change master. Bleed system and you should be fine

Jul 11, 2009 | 1995 Jeep Wrangler

2 Answers

91 mr2 shifter locking


Just a thought
We had problem with gear being difficult to select.
Found that one of the gearbox to engine bolts was loose.
Difficult to get to them but when tightened the gears select ok.

Dec 15, 2008 | 1991 Toyota MR2

Not finding what you are looking for?
2002 Audi TT Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...