Question about Toyota Passenger

1 Answer

The brakes on my 2000 revo glx goes hollow often, sometimes it holds too much.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 114 Answers

Have ur brakes adjusted

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Toyota Revo GLX, model 2001 with powered side mirror. From stored position (folded on the side of the window) to open position ( when you are going to use the side mirror), there is a clicking and...


Hi MVN, Seems that the washer is from the securing hollow mount. There should be a nut somewhere inside too. The mirror is electrically operated not hydrolic. The mirror will probably break if you try to remove it from the housing, but as to save it you will have to do so anyway, you may as well try. If you are successful, you can reattach it using double sided mirror tape, but make sure it is a good quality tape. Adjust it to the maximum and insert a flat blade between it and the mounting and try un-clipping it. If it does not break you should be able to replace and lock the housing back in place, but it will be difficult. To replace the mirror you will need to remove the door panel and the small cover on the inside of the door adjacent to the mirror mount. It clips into place and is gently levered off. Inside are three screws holding the assembly in place. Disconnect the electrics inside the door panel and then remove the screws. Fit back the replacement and reassemble. Regards John

Aug 18, 2012 | Toyota Cars & Trucks

2 Answers

2002 jeep oil light comes one when it is cold outside. as vehicle warms up (20 miles) or the engine slows down (stop lights) the light goes off. Mechanic has change oil light sensor, changed oil, said...


Has he fitted the correct pressure switch. You need one that goes open circuit under pressure, unlike brake system switch that goes short circuit when under pressure.

Nov 25, 2017 | 2002 Jeep Liberty

1 Answer

2000 silerado sometimes brake pedel goes to floor on low speed stops


Brake pedal shouldn't go to floor for any reason. Check brake fluid level. If high, then there is a problem with the master cylinder.

If the fluid is low, add until the proper level and check for leaks in the brake lines.

Is there an ABS light on?

Nov 06, 2010 | 2000 Chevrolet Silverado

2 Answers

Vaccum line fell off rear end not sure where it belongs


the vent tube for the ring and pinion housing is the only tubing made of rubber for the axle

Feb 14, 2010 | 1997 Dodge Ram 2500 Club Cab

1 Answer

Car goes berzerk


did it do this befor the other parts were replaced. sounds like some wires touching or grounding out.

Jul 10, 2009 | 2000 Cadillac Seville

1 Answer

Trying to replace my heater core for a 1994 Volkswagen Passat GLX VR6 2.8L can't find repair manual can anyone help?


take everything out, except the steering wheel and brake pedal, its th only way, seems complicated, but just tackle it, it goes quick. label things that you take apart and pay attention to how to route the wires again. the clips that hold together the vent system are a pain, I ended up not putting a few back on, big deal.

Apr 22, 2009 | 1994 Volkswagen Passat

1 Answer

Brake problems 2000 jeep cherokee


this vehicle has three sensors two front and one on the rear end this sounds like most of your problems but have all your brakes checked .thank for your question

Feb 01, 2009 | 2000 Jeep Grand Cherokee

2 Answers

2000 accent clutch is soft


There is a bearing that presses on flat springs of the clutch plate and slides back and forth on a hollow tube when you press the pedal. These can get fouled with road crud and then hang now and then when you press the pedal and perhaps not fully disengage the clutch as it should producing either a stiff action or even worse, the gnashing of gear teeth. Some bell housings have inspection plates that can provide enough access to use some cleaner/lubricant on the hollow shaft on which the 'throwout' bearing must slide. 

Sep 30, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8725 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...