Question about 1987 Ford Bronco

1 Answer

When i pull out the switch for the headlights the radio turns off, and when i also pull out the switch the right turn signal light comes on, when the headlights are on and i click high bean the radio also turns off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,340 Answers

So the headlight switch on the dash and not the steering column correct?Is high beam activated by the dash too?Is it a factory stereo or aftermarket on( Sony,Panasonic etc.).Also,how long has this been going on?Is there any repair that was done which coincided with this problem.I'll be checking for answers ASAP.Thanks,Greg

Posted on Aug 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right brake light doesn't work with lights on. Switched R bulb and socket to left, and it works. Radio also goes off when headlights r applied. But radio comes on when I turn dimmer switch all the


check for power and ground. One should be at battery voltage and the other ground. Somet5imes ground can't handle the current from the bulb so try to make a connection to ground. I try to either use the fuel tank or run a wire from the battery.
Second reason the turn signal switch can go bad and keep the battery voltage from reaching the bulb. I will also assume you checked the bulb on the other side that you know works fine. I use electrical contact cleaner inside turn signal switch. Move the lever
rapidly to clear any possible dirt.
Mage Talesin

Jan 17, 2013 | 1997 Dodge Dakota

1 Answer

2002 ford focus headlights inop


All types of car headlight problem troubleshooting.Click the link below :---All headlights not working? http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html
---------This will help.Thanks.

Feb 12, 2012 | 2002 Ford Focus

1 Answer

Head lighst do not come on all other lights work


Check the fuses, I am not sure if the 1990's had a headlight relay or not (My 1987 Cabriolet does not) but if there is a head light relay its by the battery, if there is one, put your ear down by it and have someone turn the headlights on, you should hear a click.

Also, the turn signal switch/cruise control switch, pull it forward towards the steering wheel and see if the lights come on. If the headlights come on when you pull that assembly towards the steering wheel I am thinking you have a bad headlight switch.

Jul 05, 2011 | 1990 Volkswagen Cabriolet

1 Answer

I have a 1983 Chevy S10 pickup. With headlights off all gauges work normal. When you pull the headlight switch on all the panel lights except the windshield wiper switch locator light never turn on and all...


take a look at the dash ground wire located next to the right of ebrake release handle. if the bole holding the ground wire is loose, which was quite common it will cause all kinds of feed back problems, like described in the comments section to your question.

Dec 11, 2010 | 1983 Chevrolet S-10

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

2 Answers

83 CJ7 head lights, parking lights and turn signals problems.


TRY REPLACEING THE DIMMER SWITCH,THEY CAN CAUSE WIERD THINGS TO HAPPEN.

Oct 02, 2009 | 1983 Jeep CJ7

1 Answer

Electrical problem


Find the ground wire on one of the lights and add another ground wire to a good clean metal surface and see if that fixes the problem. It defently sounds like a ground problem at one of the lights.

Jan 07, 2009 | 1983 Chevrolet Caprice

3 Answers

Head lamp switch removal


if switch is mounted on turn signal lever: remove steering column covers screws are on the bottom of lower cover. once covers are removed you should see mounting screws for the multi-switch(thats what they call headlight/turn signal switch combo). remove screws and connectors & replace switch w/new and reverse procedure.

Nov 01, 2008 | 1992 Jeep Cherokee Sport

1 Answer

Jeep88


try making sure all the grounds are good

Oct 06, 2008 | 1988 Jeep Comanche

Not finding what you are looking for?
Cars & Trucks Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...