Question about 1986 Chrysler LeBaron

1 Answer

Chrysler lebaron 1977. car doesnt start. think it is inginition switch. intermitent problem. i would like to know how to by pass the ignition so I do not have to spend **** loads of money and dont want to have to worry about it not starting (because then i could start it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 114 Answers

The switch has nothing to do with actual ignition it controls spark, time, constant live juice (electricity) abr.ECM electronic control module another name for it 1 of 2 brains for a car

Posted on Aug 31, 2010

  • MARJOREE GROOMES Aug 31, 2010

    the ignition switch is the ecm electronic control moldule if there is a distributor on a car its located on bottom of if its a car like urs its located in/on coil the spark plug wires connect one end ur spark plug other end plug to ur coils this car more likely three side by side replace all three should solve ur problem

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intermitent starting


On some models you can remove the pump from the side of the gas tank. On the others, you have to drop the tank to get the pump out of the top.

Jun 21, 2013 | 1986 Chrysler LeBaron

1 Answer

89 lebaron fuse power


change the electrical switch on the back of the ignition switch as these fuses are powered from the ignition switch

Jun 09, 2012 | 1989 Chrysler LeBaron

1 Answer

How to replace a 1984 Chrysler Lebaron ignition switch


the ignition switch is located under the dash on the steering column and is simple....
disconnect connector, remove to screws and replace switch

if however, you mean the ignition tumbler, the place where you put the key, then it a lot tougher


Jun 04, 2010 | 1984 Chrysler LeBaron

2 Answers

Ignition switch 1992 Lebaron


Hello! Disconnect +battery cable...Remove tilt lever...Remove 3 Torx column cover attaching screws...Then the upper and lower column column covers...Using a Torx with a security tip (also called tamper proof tip) #440-tx20H... Remove 3 ignition switch mounting screws...Carefully pull switch away from column...Release 2 connector locks on 7 terminal wiring connector...Then disconnect from ignition switch...Release connection lock on 4 terminal connector...Then disconnect from ignition switch.

Guru..................saailer

Jan 12, 2010 | 1992 Chrysler Lebaron

1 Answer

1994 chrysler lebaron 3.0 Ignition started


You have lost the accessory power feed due to high resistance at the ignition switch connector.
Most likely the switch will need to be replaced and if the harness plug is not heat damaged too bad you may be able to clean and crimped the terminals a little for better contact. In some cases you can buy just the connector end from the dealer as a repair part.

Dec 27, 2009 | 1994 Chrysler LeBaron

1 Answer

1989 Chrysler Lebaron 2.5 Turbo Running slugglish


hallo
check if you have a spark when engine dies. if not, check the rpm sensor or ignition coil. both have the simptoms like you describe.

marko

Oct 08, 2009 | 1989 Chrysler LeBaron

1 Answer

1987 LeBaron won't start unless I pour gas into


Check you injector seals,you may be losing pressure in the fuel lines

Jul 16, 2009 | 1987 Chrysler LeBaron

1 Answer

95 chrysler lebaron gtc 3.0 starts for a second and then stalls out


What is the fuel pressure reading at the fuel rail?

Mar 19, 2009 | 1995 Chrysler LeBaron

1 Answer

Lebaron won't start


I had a similar problem with my 90 LeBaron. It turned out to be the computer.

Dec 29, 2008 | 1992 Chrysler Lebaron

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...