Question about 2003 Volkswagen Jetta TDI
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
check the relay before removing window to remove the window remove the cover off the door inside and you will see the arm holding the window
Posted on May 06, 2009
SOURCE: Replacing the broken cup holder
First, you must remove the floor console bezel (the trim piece that surrounds the shifter knob). The proper method to remove this involves removing the shifter knob first. This is held in by a small set screw on the "radio" side of the knob. To remove the screw, you will need a small "hex-key" (also known as Allen key or Allen wrench). The proper size is 3mm, but you can get away with using a size 7/64" if you need to. Once loosened, I believe that the knob pulls right up and off. Make sure you do not lose the small screw. Also be careful not to accidentally contact the tip-top of the shifter while the knob is removed, as this may break off the small black plastic tip, which will require much more work to repair and/or replace the entire shifter.
Next, you should be able to remove the floor console bezel by prying gently and carefully on the corners and sides of the piece with a tool called a trim stick, or if you do not have this tool, you can get away with using a small, thin-tipped flat head screwdriver. However, this will almost surely cause some aesthetic damage to the edges of the trim.
Once this bezel is out of the way, (you shouldn't have to remove the electrical connectors on the underside of the bezel for this specific job) there are 2 screws holding down the bottom of the cupholder assembly. I believe these are both Torx - type screws, which will need either a T10, T15, or T20 screwdriver bit to remove(I'm sorry but I don't remember exactly which of the 3 sizes are used). After these 2 screws are removed, open the armrest. On the TOP of the FRONT of the armrest, just above the cupholders, are 2 more screws which should be the same as the 2 bottom screws. Remove these, then lift the cupholder assembly up and forward to remove it.
To install, simply reverse the above procedure.
Because this is my first solution posted on this site, I would love to have your feedback. Please let me know how everything goes with this project. Thank you!
Posted on May 27, 2009
SOURCE: Reset Computer
I suppose it is the same as for other VAG cars.
Press the trip meter reset button while turning on the ignition and keep it pressed for a couple of seconds.
Posted on Jul 12, 2009
SOURCE: vw sharan timing belt change?
your getting close to a change, especially if its a belt and not a chain. i know friends that had there belts changed out anywhere from 60k to 90k. Chains can go about twice as long as a belt. i you kept this car up on it servicing and dont abuse it. i"d say it"ll last till at least 70k.
Posted on Oct 04, 2009
Tips for a great answer:
Jul 13, 2015 | Volkswagen Cars & Trucks
May 19, 2012 | Volkswagen Sharan Cars & Trucks
Aug 28, 2010 | 1997 Volkswagen Eurovan
Mar 09, 2010 | Volkswagen Microbus Cars & Trucks
Jul 12, 2009 | Volkswagen CC Cars & Trucks
May 13, 2009 | 2001 Hyundai Accent
Apr 10, 2009 | 2005 Mercury Monterey
Apr 04, 2009 | 2003 Volkswagen Eurovan
332 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: