Question about 2004 Chrysler Sebring

1 Answer

Just purchased a 04 Chrysler Sebring 2.4L Conv. 2 wks ago. The very next day when I was driving it when I would come to a stop light the car would start idling really low and acted like it was going to stall out. Took it back to the dealer and they said it was proly just bad gasoline(the car had been sitting for awhile). They said not to worry the car just needs to be driven a little and the problem should correct itself. Well couple days later the problem stopped after I filled the tank@the gastation. A week later it started again so the dealer had the machanic look at it. They said there were no problems found when they took it for a test run. After I took it back home it drove fine for approx. 4 days, then the oil light on dash came on. Brought it in for an oil change, things seemed fine for a week. All the sudden my oil light came back on when coming to a stoplight and my car almost stalled out 3 times while driving home. When I would step on the gas the oil light would turn itself off and it would drive ok but at every stop the oil light would come back on and car would almost stall. Checked the oil, is at normal level. PLEASE HELP!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This fix works for 2.7L engine. Worth having your mechanic look at.

Answer
NO: 08-36-99
SUBJECT: Engine Oil Pressure Light Flicker
DATE: Oct. 15, 1999
OVERVIEW:
This bulletin involves adding a terminal/wire/vent to the oil pressure switch connector.

NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A 2.7L ENGINE.

SYMPTOM/CONDITION:
With a hot engine the oil pressure light may be on or flicker on at idle.

DIAGNOSIS:
Verify engine oil pressure as described on page 9-21 of the 1999 Concorde/Intrepid/LHS/300M service manual (Publication No. 81-270-9140). If engine oil pressure is within specification perform the Repair Procedure.

PARTS REQUIRED:
Qty Part No. Description
1 05017800AA Wire Terminal/Vent


REPAIR PROCEDURE:
Raise vehicle on a suitable hoist.
Remove engine oil pressure switch connector from switch.
Remove sealing dart from the empty cavity at the rear of the connector.
Pull terminal locking ring outward from front (switch) side of connector to gain access to terminal locking tabs.
Install wire terminal/vent, p/n 05017800AA, in place of the removed sealing dart. Slide locking ring back into place.
Attach the connector back on the oil pressure switch.
Spot tape the wire/vent to follow the harness towards the top of the engine compartment.

Posted on Sep 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Starter is new and won't engage the flywheel.


2003 Chrysler Sebring 2.4L SFI 4cyl ' Repair Guides ...

www.autozone.com/.../repairGuideContent.jsp?...Starter...
AutoZoneAutoZone Repair Guide for your 2003 Chrysler Sebring 2.4L SFI 4cyl Engine Electrical ... Bad starter drive or flywheel-driven gear. ... Starter Spins Freely, Won't Engage ....Center the snapring on top of the shaft (use a new snapring if the original was ...Vehicle + Keyword: 04 Toyota Camry oil filter, battery 2005 Silverado.

Sep 18, 2015 | 2005 Chrysler Sebring Conv

1 Answer

07 Chrysler Sebring still not running right after replacing catalytic converter... please help a gal out!


Stop using it,the flashing light is a Class A converter ruining
misifire,so nothing was fixed so far

Sounds like you have cylinder misfires that ruined the
converter & only the converter was replaced.

The last thing you do, is the converter, AFTER you diagnose the systems to find out why it failed

Sep 29, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

Fuel Rail Leak


Did did you change the o-ring at the fuel line to fuel rail connector? Do that before you change the fuel rail. According to an e-bay seller who is selling a used fuel rail from his salvage shop, the following fuel rails are interchangeable.
300 05-10 Fuel Injector; 2.7L and 3.5L
AVENGER 08-10 Fuel Injector; 2.7L
AVENGER 08-10 Fuel Injector; 3.5L
CARAVAN 08-10 Fuel Injector; 4.0L
CHALLENGER 09-10 Fuel Injector; 3.5L
CHARGER 06-10 Fuel Injector; 2.7L and 3.5L
JOURNEY 09-10 Fuel Injector; 2.7L
JOURNEY 09-10 Fuel Injector; 3.5L
MAGNUM 05-08 Fuel Injector; 2.7L and 3.5L
NITRO 07-11 Fuel Injector; 4.0L
PACIFICA 05-06 Fuel Injector; 3.5L
PACIFICA 07-08 Fuel Injector; 4.0L
SEBRING 04 Fuel Injector; Conv, 2.7L, from 07/30/03
SEBRING 04 Fuel Injector; Sdn, 2.7L, from 07/30/03
SEBRING 05 Fuel Injector; Conv, 2.7L
SEBRING 05 Fuel Injector; Sdn, 2.7L
SEBRING 06 Fuel Injector; (Conv, Sdn), 2.7L
SEBRING 07 Fuel Injector; (Sdn), 2.7L
SEBRING 07 Fuel Injector; (Sdn), 3.5L
SEBRING 08-10 Fuel Injector; (Conv, Sdn), 2.7L
SEBRING 08-10 Fuel Injector; (Conv, Sdn), 3.5L
STRATUS 04 Fuel Injector; Sdn, 2.7L, from 07/30/03
STRATUS 05 Fuel Injector; Sdn, 2.7L
STRATUS 06 Fuel Injector; (Sdn), 2.7L
TOWN & COUNTRY 08-10 Fuel Injector; 4.0L

Mar 04, 2014 | 2007 Chrysler Pacifica Touring

1 Answer

2002 Sebring conv. the turn signals, radio, and


the fuse box under the dash is also a body control module a computer have it checked

Aug 27, 2013 | 2004 Chrysler Sebring

1 Answer

I have an '04 Chrysler Sebring Conv. 6 cyl with an error code of P 1296. What does that error code mean ?


CODE P1296 - 5 VOLT VREF SUPPLY NOT PRESENT - POSSIBLE CAUSE MAP SENSOR VREF CIRCUIT OPEN BETWEEN THE SENSOR AND PCM / MAP SENSOR GROUND CIRCUIT OPEN BETWEEN THE SENSOR AND PCM / MAP SENSOR IS DAMAGED OR HAS FAILED / PCM HAS FAILED.

Nov 09, 2010 | 2004 Chrysler Sebring

1 Answer

2008 sebring convertivble -m wont shift


if was running fine and and next day just wont go y woulthink is probably oyu input or output speed sensor,oyu need to check it with scanner and see if is that is the problem and not you tranny brain

Sep 27, 2009 | 2008 Chrysler Sebring Convertible

1 Answer

1996 Chrysler Sebring Conv.- Power Drain or Damaged Crank Sensor?


try checking the secondary ground wire that comes off the battery see if its loose or corroded might help

May 29, 2009 | 1996 Chrysler Sebring

3 Answers

Oil light??


I was lucky on mine. It was just a bad oil sender switch that needed to replaced, plus the cable connector up-grade. Oil was leaking past the switch. Oil pressure was measured at full spec, both at idel and running.

Dec 27, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
2004 Chrysler Sebring Logo

723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...