Question about 1989 Honda Accord 4 Door

Open Question

How many bolts on a 1989 honda accord starter and where are they? what is the level of difficulty to remove and replace?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

philschneide
  • 448 Answers

SOURCE: how to remove starter from 1998 honda accord

Detach the cable from the negative terminal of the battery. Caution: If you have an anti-theft radio, make sure you have the activation code before disconnecting the battery.

Remove the battery and battery tray from the engine compartment (remove the battery first, then remove the bolts for the battery tray and remove it.).

Remove the lower radiator hose and the wiring harness from the starter bracket. Make sure they are positioned out of the way.

Clearly label, then disconnect the wires from the terminals on the starter motor solenoid (the smaller cylinder attached to the starter). Disconnect any clips securing the wiring to the starter.

Remove the mounting bolts (two) and detach the starter (pull it gently out of its housing).

Reverse this procedure for installation.

Hope this is of help to you.

Posted on Dec 26, 2009

  • 11 Answers

SOURCE: T would like to know the steps to remove the front rotors.

You can try a couple of things. First the most common is try spraying it with something like WD40 or get a breaker bar which will give you more power to turn it and will add alot more tension so the bolt will break loose. Could be that the heat seized it there but try these steps.

Posted on Mar 24, 2009

co7196
  • 3433 Answers

SOURCE: cannot remove harmonic balancer bolt on 96 honda (2.2L)

You may need an impact gun. If loctite was used, you will need a gun.

Posted on Sep 13, 2009

  • 819 Answers

SOURCE: how to remove starter solenoid from 1998 honda accord LX 4cyl?

the starter solenoid is integral to the starter.

Posted on Dec 26, 2009

Ford Guroo
  • 71 Answers

SOURCE: how to replace rear struts on 2003 honda accord

You will need to rent a spring compressor or borrow one from advance auto parts. The access ports are usually in the back of the car, some have plastic caps over them usually about 6 inches square and some you have to take the inside trim panel off in the car to gain access. Do not attempt to take the struts out without a spring compressor or you will get hurt as the springs are under a lot of pressure so when un bolted without the proper tool they can come apart and you will for sure need a stich or two.

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install starter on 2007 honda accord lx 2.4l


I'm confuzzed. Does an Acer have a Honda accord starter?

Disconnect the + battery cable. Disconnect all wires on the starter, and remove the mounting bolts. Wiggle the starter out of the engine bay, and replace with the one you want to use. Reinstall the bolts and wires, and reconnect the battery + wire.

Dec 19, 2012 | Cars & Trucks

1 Answer

Removing the starter


First you want to determine the reset code for your factory installed stereo system. The anti-theft system in place will shut down when you disconnect the battery cables. You will need the reset code for your stereo to remove starter.

Park your Honda Accord on a level surface, activate the emergency brake and place blocks behind the back tires for safety. Disconnect the negative battery cable with a terminal puller. Disconnect the positive battery cable. Raise the front end of the car with a jack for easier access to the starter.

Remove the starter motor wiring harness in 2.2L, 2.3L and 2.7L engines. In 2.2L and 2.3L engines, your next step is to find the bracket on the starter motor and disconnect the lower radiator hose. In 3.0L engines, you need to remove the Automatic Transmission Fluid (ATF) cooler.

Locate and remove the starter cable from terminal-B on the back of the solenoid (for all four engine sizes). Disconnect the black and white cable from the S-terminal.

Unfasten the two starter mounting bolts from the transaxle assembly. Remove the third mounting bolt at the back of the starter. Place all bolts and nuts in the baby food jar to prevent loss. Remove the malfunctioning starter.

Take your malfunctioning starter to the parts store with you. Aftermarket distributors remanufacture most of the starters they sell, so you can likely obtain a partial credit toward your new starter by exchanging your old one. Be sure that you take care not to damage the starter in transit, because the better condition it is in, the more you can get for it.

Purchase a replacement starter that has the same or higher cranking capacity (power rating) as the original starter in your Honda Accord. Also, match the bolt patterns, drive gears and electrical connections. Your owner's manual may list specifications or the auto parts technician will help you determine them.

Hope this helps

Mar 02, 2011 | 1996 Honda Accord

1 Answer

Replace starter on 2003 Honda Accord w/4 cylinder. Steps to take to remove and install new starter.


disconnect the cable to the battery........there is 3 bolt holding the starter to the engine/transmission housing. You may need to remove the air intake manifold to gain access to the work area.

Mar 20, 2010 | 2003 Honda Accord

3 Answers

Starter for 2004 honda accord


Is this for a 4 or 6 cylinder engine?

If it is for the 4 cylinder, it's not that easy as the intake manifiold needs to be removed before the starter can be removed as the starter is under the intake manifold. Once the manifold is removed then it's a matter of a couple bolts and connections. It's not that quick a job.

Aug 19, 2009 | 2004 Honda Accord

1 Answer

New starter in 1997 honda accord. Bolt closest to


is it in the starter or the trans? In the starter, replace the starter. In the trans, you may need to have someone repair the threads with helicoil, or you can put some locktight on the bolt, get it fairly tight, and it should set up.

Jul 03, 2009 | 1997 Honda Accord

1 Answer

Where is the bolts to remove a 85 honda accord starter???


if youve found the starter motor there are 2 bolt diagnolly across from eeach other12mm from memory. if you cant find the starter look for where the gearbox meets the engine and follow the line

Jun 17, 2009 | 1985 Honda Accord

2 Answers

Removing starter


It's not that easy. Yes, 2 bolts hold the starter down but you have to remove the whole intake manifold to access the starter to remove it.

May 30, 2009 | 2003 Honda Accord

1 Answer

1989 honda accord 4 dr--new battery--starter will not start


make sure your getting full contact with you main positive and ground if nor another thing can be you fuel pump you can try replacing that also

Mar 16, 2009 | 1989 Honda Accord 4 Door

2 Answers

Question about hondas


1990-1993 what?/ honda accord fit a 1989 honda accord?

Jun 20, 2008 | 1989 Honda Accord 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...