Question about Chevrolet Silverado 1500

1 Answer

Where can i locate a picture or diagram of the starter for my 6 cylinder c1500 1997 silverado so i know where the bolts are located to remove it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Good Evening, I do not have a picture tho I can tell you most general motors starters are 2 bolts going from the bottom up you cannot miss them. Just be sure to disconnect power *battery* and not overtighten the new nuts when you secure your wires down. I hope this helps, and if you have any more questions please feel free to ask.
Thanks,
Joey

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where the starter located in a 2000 LW2 4 cylinder


the LW2 comes with a 6 cylinder. The starter is located on the backside of the motor (firewall side) where the motor bolts to the transmission.

The LW1 comes with a 4 cylinder. the starter is located on the front of the motor (radiator side) where the motor bolts to the block. If you crawl under the car you will see it.

Sep 16, 2015 | Cars & Trucks

1 Answer

Torque specs and sequence of head bolts 2004 chevy silverado 2500hd with 6.0


Go to autozone.com and become a member of their web-site. It is FREE. You can then access repair info for your vehicle. There are repair manuals that show pictures and everything. I will look for your torque specs and picture.
  • Clean the cylinder head bolts, apply sealer to the threads, and hand-tighten.
  • Tighten the cylinder head bolts:
    1. M11 cylinder head bolts first pass in sequence to 30 Nm (22 ft. lbs.).
    2. M11 cylinder head bolts second pass in sequence + 90 degrees.
    3. M11 cylinder head bolts (1,2,3,4,5,6,7,8) + 90 degrees
    4. M11 cylinder head bolts (9 and 10) + 50 degrees
    5. M8 cylinder head bolts (11,12,13,14,15) to 30 Nm (22 ft. lbs.). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
      NOTE The cylinder head gasket displacement can be verified by markings visible on the underside of the right gasket locating tab. Some 4.8/5.3L head gaskets may have 53 stamped onto the locating tab. Some 6.0L head gaskets may have 60 stamped onto the locating tab.
  • 0996b43f8022f63f.jpg

    Aug 28, 2014 | 2004 Chevrolet Silverado 2500HD

    2 Answers

    Looking for a picture of the diagram of where the thermostat is located on my 1998 2.7 liter dodge intrepid PLEASE!!!!!


    Hi, I don't have a picture, but trace the big hose from the bottom of the radiator to the engine, and it will be under the housing where the hose connects.


    2.7L Engine

    1. Disconnect negative cable.
      CAUTION Do not remove pressure cap with the system hot and under pressure because serious burns from coolant can occur.
    2. Drain cooling system.
    3. Remove radiator lower hose from thermostat housing.
    4. Remove nuts from heater tube flange studs.
    5. Loosen starter bolt at heater tube bracket.
    6. Pull heater tube out of thermostat housing and position out of the way.
    7. Remove bolt and two studs.
    8. Remove thermostat housing, O-ring and thermostat.
    9. Remove thermostat housing bolts.

    To install:
    1. Clean gasket sealing surfaces.
      NOTE Install thermostat with the bleed valve located at the 12 o'clock position, between tabs on seal.
    2. Install thermostat and seal into thermostat housing .
    3. If removed, install two studs.
    4. Install thermostat, thermostat housing and O-ring and bolt. Tighten attaching bolts to 105 inch lbs.(12 Nm).
    5. Lubricate new heater return tube O-ring with coolant.
    6. Position heater return tube flange over two studs. Install nuts.
    7. Tighten retaining nuts to 53 inch lbs.(6 Nm).
    8. Tighten starter bolt to 40 ft. lbs. (54.3 Nm).
    9. Connect the lower radiator hose to the thermostat housing. Install hose clamps.
    10. Refill cooling system.
    11. Inspect for leaks.
    12. Connect negative cable.

    Mar 26, 2011 | 1999 Dodge Intrepid

    2 Answers

    Where is the starter located?


    without knowing make and model and year almost imposibe to telll exact location but should be on rear left or right side of motor right where tranismison bolts to motor

    Nov 13, 2010 | GMC Denali Cars & Trucks

    2 Answers

    I am trying to locate the starter of my 1998 LS 400 pls. help me.


    The starter is located under the intake manifold on this engine.

    20d8b81.gif

    Jun 17, 2009 | 1998 Lexus Gs 400

    1 Answer

    Bad starter. how do you remove. how many bolts are there??


    once you have located the starter ther are two bolts and two wires the bolts are located directly accross from eachother on each side of the starter the wires are on the back of starter hope i could help

    Mar 23, 2009 | 1986 Chevrolet Celebrity

    1 Answer

    Where is the crankshaft position sensor located on a 2006 chevrol


    on 2.2 models remove starter. disconnect 7x crankshaft position sensor wiring harness.remove sensor mounting bolt, with draw sensor, replace o ring and lightly lubricate it with oil.... on 6 cylinder models,..remove the drive belt, jack up car, remove crankshaft pulley. remove sensor bolt and pull out.( noting the wiring harness for installation).

    Dec 24, 2008 | 2006 Chevrolet Malibu

    1 Answer

    Diagram needed


    you really don't need one.....
    1.Disconnect the battery
    2.locate the starter. If its a v8 itll be on the driver side at the back of the engine beside the oil pan
    3.there are two bolts on the bottom of the starter that you need to remove with a 9/16 socket or wrench.(support the starter when you remove the last bolt so the wires don't get broken)
    4.observe the location of all of the wires attached to the starter(make a diagram so you don't forget where they go)
    5.Remove the nuts that hold the wires on the starter.(make sure the ring connectors and wires are in good shape if you notice any damaged ones they should be replaced)
    6. reverse procedure to install new one
    ..............hope this is helpfull.good luck!

    Dec 10, 2008 | 1995 Chevrolet Lumina

    1 Answer

    Starter replacement - 1991 Toyota previa


    Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

    Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
    See Figures 5 through 12
    1. Disconnect the negative battery cable from the battery.
    2. Raise and safely support the vehicle.
    3. If equipped with 4WD, remove the front driveshaft.
    4. Remove the nut and disconnect the starter wire.
    0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
    1. Disconnect the starter connector.
    0900c15280089fbc.jpgFig. 6: Remove the cap hiding the nut 0900c15280089fbd.jpgFig. 7: It will be necessary to use an extension to remove the nut
    1. Remove the bolt holding the starter stay to the upper stiffener plate.
    2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
    3. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
    0900c15280089fbe.jpgFig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
    1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts. Tighten the bolts as follows:
      • Bolt A to 41 ft. lbs. (56 Nm)
      • Bolt B to 30 ft. lbs. (41 Nm)
    0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
    1. If equipped with 2WD, install the starter, nut and three bolts. Tighten the bolts as follows:
      • Bolt A to 41 ft. lbs. (56 Nm)
      • Bolt B to 30 ft. lbs. (41 Nm)
    0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
    1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
    2. Install the starter connector.
    3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
    4. If equipped with 4WD, install the front driveshaft.
    5. Connect the negative battery cable.
    SOLENOID REPLACEMENT
    The starter solenoid (magnetic switch) is an integral part of the starter assembly.
    1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
    2. Disconnect the wire lead from the magnetic switch terminal.
    3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
    4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
    To install:
    1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
    2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
    3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
    There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
    1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
    2. Reinstall the starter on the vehicle. Check starter system for proper operation.

    Nov 23, 2008 | 1991 Toyota Previa

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    57 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8531 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...