Question about 2005 Dodge Ram 2500 Truck

Open Question

Need the pinout of the APPS to ECM on 2005 Dodge cummins

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: need to know torque settings on water pump

torque them to 18 ft/lb.

Posted on Feb 10, 2009

  • 3 Answers

SOURCE: water pump replacement procedure 2005 2500 dodge with cummins diesel

take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Posted on Mar 22, 2009

  • 28 Answers

SOURCE: how do reset a 2005 dodge 2500 cummins

If you are talking about resetting the codes of the computer, most cars can be done by just disconnecting the battery for about 5 minutes.

Posted on Apr 30, 2010

  • 1 Answer

SOURCE: I need the injector circuit wiring diagram for a

What part of the circuit do you require?

go to www.dieseltruckresource.com

It's a really good forum for dodge diesel owners. Ask the question there and you should get all the help you need.

Posted on Jul 05, 2010

jturcotte
  • 7772 Answers

SOURCE: I need a belt diagarm

from autozone.com--one for with A/C, one for no A/C


536103d.jpg

61ca424.jpg

Posted on Sep 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998.5 Dodge Ram with 24valve Cummins...When swapping a bad ecm with a known working ecm, must i also swap pcm to match?


No, but the calibration numbers on the ecm must match.In 1998 dodge still used a prom, that you need to take out of old unit and put in new unit

Dec 01, 2014 | Dodge Ram Cars & Trucks

2 Answers

Need a diagram for installing the fan belt


Need a diagram for the ECM A and ECM B pinouts on a 05 Dodge 2500 Cummins HO 5.9L.

Sep 03, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

How do reset a 2005 dodge 2500 cummins


If you are talking about resetting the codes of the computer, most cars can be done by just disconnecting the battery for about 5 minutes.

Apr 29, 2010 | 2005 Dodge Ram 2500 Truck

2 Answers

02 dodgeram 2500 4x4 manual tran with 24valve 5.9 cummins lift pump went bad than after replacing truck ran rough intermittinally + ck eng lite comes on, so replaced vp inj pump n lost 1 code still 4...


high voltage is an indication something is not plugged in or plugged in wrong. You will need to test the harness to see if the required voltage supply is present, connector unplugged, if not then your going to have to determine if the siganl comes from the PCM or the fuse block. If its the PCM you may have a bad PCM. Same thing for the ground side. Now if the reference signal and ground are good you could have a sensor issue but I doubt this because you have high voltage on three components. This tells me that three component signals are not getting back to the PCM. This is why it sets the codes. With all the work you just did I suspect you didnt but the wiring back the way it was. Sometimes people take the ground wire off between the engine and and body because its in the way and don't reinstall it. Or don't tighten it enough. With todays electronics there simple mistakes cause unforeseen issues.

Nov 24, 2009 | Dodge Pickup Cars & Trucks

2 Answers

1999 DODGE CUMMINS SHUT DOWN FAULT CODES p1689, p1688


P-1689 NO COMMUNICATION BETWEEN ECM & INJECTION
PUMP MODULE

Jul 21, 2009 | 2000 Dodge Ram 3500

1 Answer

Where is oil pressure sensor located on 2001 dodge 2500 cummins?


Hello mhak330: My name is Roger and I can give you the answer to your question. Locate the ECM on the drivers side of the engine.look for the bottom bolt holding the ECM. To the right of the bolt you should see the oil pressure sender unit. Should you need further help please just ask. Please rate the quality of your answer. This way we know you received helpful information. Thank You for using Fix Ya. Roger

Jul 07, 2009 | 2006 Dodge Ram 2500

2 Answers

Reset turbo boost relay 2003 Cummins


You will find step by step instructions on this software .. Download from here: Cummins Signature ISX and QSX15 Factory Manual Repair Servic Download...

Jun 08, 2009 | 2005 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...