Question about 1987 Chevrolet V30

Open Question

How do you replace the locking cylinder in the ignition switch on a 1987 P30 chevy stepvan? the switch is on the dash.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: replace ignition lock cylinder 1996 BMW 318i with 1995 BMW

no you can not

Posted on Mar 12, 2009

Ad
  • 1 Answer

SOURCE: Key will not turn ignition switch.

try sanding down the key alittle - saved me a fortune on my 96 civic

Posted on Apr 30, 2009

  • 154 Answers

SOURCE: ignition switch cylinder replacement

take off the steering wheel, remove the plastic piece on the steering column and then the ignition should unbolt and slide off.

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: 1997 chevy blazer ignition switch

1997 blazer put car in park shut it off but, key won't turn far enough back to come out

Posted on Jan 02, 2010

ftw1952
  • 10319 Answers

SOURCE: how to remove and replace the ignition switch

Remove the horn button, nut the pull the wheel off with a puller.Remove the lock plate retaining spring using a Lock plate press. Remove the directional switch screws (3).. Lift that switch out of the way to remove the ignition lock screww
Pull out ign Lock Cylinder

Reverse this procedure to install

Posted on Jun 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT KIND OF TRANSMISSION IS IN MY RV? IT HAS A CHEVY 454 ENGINE.


454 chevy engine in motorhome - RV-Coach Online

www.rv-coach.com > Discussion Forum > Mechanic's Corner - Engines
Mar 25, 2010 - I have a 1995 winnebago elanden Chevy chasis and Chevy 454 motor.... I am trying to tighten or replace all the belt on my 1987 Fleetwood Southwind ... What type trans fluid,oil and filter does the 1984 chevy rockwood motorhome take? .... Havereplace ignition switch, check neutral safety switch at transmission, all OK. RV with Chevy 454 engine problems
Oct 18, 2015
454 P30 radiator removal
Jul 23, 2012
Overdrive Transmission Conversion
Nov 6, 2010
4L80E Transmission Problems
Nov 15, 2009
More results from www.rv-coach.com

Nov 24, 2015 | Cars & Trucks

1 Answer

How do i remove the ignition switch on a 1987 chevrolet caprice to replace it lost keys?


(pain if you dont have the right tools)

also you are replacing the LOCK CYLINDER, the ignition switch is somewhere else

remove horn button

" steering wheel

" turn signal switch assy

" steering lock plate

" screw holding in lock cylinder

and it\'s not that easy

Oct 25, 2014 | Cars & Trucks

1 Answer

1985 chevrolet p30 stepvan stutters (chokes) after about 20 minutes of driving. It doesnt turn off on me just stutters. Any suggestions on what this can be?


Change the capacitor in the distributor and check the coil for overheating. Check venting of the fuel tank Check for vapour lock in the fuel lines getting to hot to the carby.

Feb 01, 2014 | Cars & Trucks

1 Answer

Ignition switch ground


I am looking, but so far, there is not ground terminal.

Nov 06, 2013 | Cars & Trucks

1 Answer

How to remove ignition switch on 1986 P30 Chevy rV chassis


1. Turn ignition switch to off position and leave the key in the switch.
2. Disconnect the battery.
3. Take a small diameter. paper clip and insert it into the small hole in the face of the ignition switch. You will feel a small button that you depress.
4. While depressing the button, turn the key to the accessory position (counter clockwise) and using the key remove the cylinder.
5. You can now remove the bezel by unscrewing it CCW.
6. This will allow you to remove the ignition switch from the dash and disconnect the wire harness plug from the rear of the switch.
7. They don't always come apart easily , and may require some Jiggling of the key and the wire.

[]p[========='//[l;. richard

Jul 09, 2010 | 1986 Chevrolet G30

1 Answer

Need to know how to remove and replace my f 150 ingention it is a 1987 and what tools i will need


The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.
The ignition switch is operated by the key switch. Courtesy of Ford Motor Company.
To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.
a4d28fb.gif

Oct 22, 2009 | 1987 Ford F 150

1 Answer

Where is the fuse box on 1987 P30 Chevy -


does the dash pad lift up on drivers side

Oct 09, 2009 | 1987 Chevrolet R30

1 Answer

Lock barrel switch


VI/WT = 50 RD/BK = 15 RD/YL = 15x RD/GN = 15r GN/WT = P or P30 Red = 30 Red = 30

Sep 17, 2008 | 1987 Mercedes-Benz Mercedes Benz 190 Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...