Question about 2001 Suzuki Xl 7

Open Question

How do I remove a starter on my 2001 Suzuki XL7

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 353 Answers

SOURCE: how do i adjust my headlingt on a 2001 suzuki xl7

Headlamp: Adjustments
- Unless otherwise obligated by local regulations, adjust headlight aiming according to the following procedure.
- After replacing headlight, be sure to perform its aiming
1. Before adjustment, make sure the following.
a. Place vehicle on a flat surface in front of blank wall as below ahead of headlight surface.
Clearance "a" between screen and headlight : 10 m (32.8 ft)
b. Adjust air pressure of all tires to a specified value respectively.
c. Bounce vehicle body up and down by hand to stabilize suspension.
d. Carry out one driver aboard.
Driver's weight : 68 kg (150 lb)
2. Check to see if hot spot (high intensity zone) of each main (low) beam axis falls as illustrated.
Hot spot specification (clearance "H") : Approx. 100 mm (3.94 in.)
3. If headlight aiming is not set properly, align it to specification by adjusting aiming gear.
4. If horizontal aiming is not set properly, check headlight installation or body bending
5e4c094.jpg 925643c.jpg 5b86853.jpg

Posted on Nov 16, 2009

  • 1986 Answers

SOURCE: how do i adjust my

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 19, 2009

Testimonial: "thanks"

  • 382 Answers

SOURCE: trying to replace alternator on SUZUKI XL7

yes use a small socket wrench as in a 1/4 in drive i had the same problem with my echoe not a lot of room to undo bolt with a bigger ratchet...As for the belt if serpitine you need to remember how to put the belt back in there should be a tensioner pulley that you need to move to remove and replace belts however swinging alternator out of way or removing same will allow some belts to be removed if only 1

Posted on Dec 21, 2009

  • 2019 Answers

SOURCE: my 2001 suzuki xl7 air conditioner blows hot air

Lots of possibilities. The first thing I would do is to have someone turn it on and off, while you look around under the hood (carefully, because fans go on and off).
The first thing you want to see, is if the AC compressor clutch is turning on and off properly. When the fan clutch is off, the outside of the pully will spin with the belt, but the inside will be standing still. When it is on, the whole pulley turns. If this does not work, then it could be a fuse, switch, or the clutch itself.
If this is working, then you need to look into the small sight glass in the top of the receiver/dryer, which is a small vertical cylinder. It should show a flow of clear fluid. Bubbles means it is low on freon.
But the controls could be screwed up, with the hot water staying on, the cold air not be allowed in, etc.'
Operating the controls should allow you to see these things working.
To go beyond this, like check the compressor, the expansion valve, etc., you would need to put a set of pressure gauges on, which are about $50, and come with instructions. There are 2 because you want to compare the input and output sides of the compressor.

Posted on Feb 08, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I take the starter off of the 2003 suzuki xl7. I know how to do the battery cable removal. I just need to know how I can remove the starter.

bat neg lug off.
gain access to starter, front in jack stands really help.
then remove all wires to starter
then any heat shields blocking access to it's mounting bolts.
then remove the 2 mounting bolts.
duck as it falls.

Oct 28, 2016 | 2003 Suzuki XL-7

1 Answer

How do i remove the starter from the suzuki xl7.

same as all cars made.
posted over 100 times.
ever youtube this, 10,000 examples on that. endless.
1: disconnect battery neg lug, first, or boom eat acid.
2: gain access to the starter. jack stand the front.
3: remove any shields covering starter , Ill assume you know where starters hide, the are at the flywheel (engine /trans juncture)
4: remove all wires, from starter.
5: remove the mounting bolts to starter.
6: it falls, you duck.

reverse above, for back, cept duck.

Oct 28, 2016 | Suzuki XL7 Cars & Trucks

1 Answer

Where is 2007 xl7 suzuki starter located?

which engine? J20, H25, H27. (all 3 same)
see that battery cable, see the plus cable, it goes to the starter.
the starter engages the flywheel, so is there, near the flywheel ring gear. and will be on the left or right side of all engines.
the V6 is right
frame 28
as are, j20 and G16 are same. place.

right side means, sitting in drivers seat, right is right.

is it dead, ?
or want to do tests and cant find it?

Apr 27, 2015 | Suzuki XL7 Cars & Trucks

1 Answer

Remove center console 2008 suzuki xl7

between seats.?
there are 3 choices for docs. to read.
a real FSM. by suzuki , book (buy one) used? at fleabay
just 4 bucks to read it

Feb 02, 2015 | 2008 Suzuki XL7

1 Answer

How do i replace the starter in a 2005 SUZUKI XL7

same as all cars
1: battery neg lug removed, tied back. (or boom happens)
2: remove all wires to starter, solenoid.and starter.
3: unbolt starter (nuts and bolts on base)
4: starter falls to earth.
reverse above to replace.

Nov 13, 2014 | 2005 Suzuki XL-7

1 Answer

I have a 2001 suzuki xl7. what is the best way to get to the starter so it can be repaired?

having theb same problem with my 2001 xl7.........been trying to find a pic daigram..looks almost impossible from the top and you know a web site location where i can find one ?????/

Sep 21, 2010 | 2001 Suzuki Grand Vitara

1 Answer

Heater core on 2005 suzuki xl7 needs replaced how?

you must remove the instrument panel, then remove cooling unit

Jun 18, 2010 | 2001 Suzuki Xl 7

2 Answers

How do I reset the engine light after a P0496 code?

Unplug the battery for 15 minutes and then plug the battery back in, but until you fix the oxeygen sensor you are going to continue to have the code thrown

Apr 29, 2009 | 2001 Suzuki Xl 7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

393 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides