Question about 1993 GMC Sierra C2500

Open Question

I need to find a clutch pedal asembly for a 2000 GMC serria 1500 with a 4.3 v6 2wd. The pedal itself is fine, the reason i'm looking for one is becuse where the master cylinder locks on the fire wall is broken. From what i understand it is all one piece. on the inside of the truck, under the dash the clutch pedal is on a big plastic bracket, This also has what holds the master. Through a hole in the fire wall. i can't seem to find that is not from the junk yard. the part number would be great. thank you

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 147 Answers

SOURCE: what transmission will fit in an 89 gmc sierra?

if it has a 4.3 liter motor a 86 to a 97 if it has a 350 motor a 81 to a 96 will work hope this helps

Posted on Nov 20, 2008

michigan man
  • 3533 Answers

SOURCE: I need a retaining clip for the arm rests on the

give these peoples a call they only sells GM-parts only its Schram auto & truck parts 1-800-292-1032 and they website is and i hope i have been some help to you Michigan Man.

Posted on Oct 06, 2009

  • 77947 Answers

SOURCE: is it fairly easy to install a clutch master

it is very easy to replace the parts, bleeding the air is the real problem, u will need to buy a Mityvac brand vacuum clutch bleeding tool, with out it you will never get the air out of the system after the parts are replaced, also always replace the clutch master and the clutch slave at the same time.

Posted on Jan 11, 2010

  • 158 Answers

SOURCE: 95 chevy 1500 v6 2wd. the transmission is

lower planetary gearset is shot. They are a weak spot in this trans. Rebuild or replace trans... they generally make alot of metal when they fail

Posted on Aug 05, 2010

  • 10319 Answers

SOURCE: I'm leaking coolint from the

Purchase a 5/8 to 3/4 hose union and connect the two heater hoses to it. Just remove the two hoses from the heater core to do this. You will not have heat this way although the leak will be fixed
The union can be purchased at most NAPA Auto parts Stores

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

98 4.3 vortex.Gmc serria 1500 where is idle control motor valve

It's on the Throttle body assembly, what the big air boot connects to, where your gas pedal cables connect to, where the filtered air enters the engine-this idle control motor, called a stepper motor, has a 4 wire connector (2 green and 2 blue wires), and is retained to the throttle body by small bolts or screws.

Nov 17, 2015 | Cars & Trucks

1 Answer

Why my 2000 gmc serria 1500 jerking on start of driving problem

I don't understand what you mean by "jerking on start driving". Are you saying that it only jerks when you take off from a start when cold or all the time? How does it run after that? Need more detailed information. My best guess at this point would be to start with a fuel filter. Sounds fuel related to me.

May 26, 2014 | 2000 GMC Sierra

1 Answer

Where's the knock sensors on a 2007 gmc serria 1500 5.3L

under the intake plentium right in the middle of the valley between the heads. bad for wires getting corroded and rusted. it holds water in the knock sensor holes, you can buy the harness

Mar 07, 2013 | 2007 GMC Sierra 1500

2 Answers

2000 gmc serria wont stay running unless you feather the gas pedal after a minute or so it will be fine after it warms up it runs great

you have a bad idle air control valve and also a thottle position sensor. both sensors are located on the throttle body

Nov 25, 2012 | 2000 GMC Sierra

1 Answer

I need answer for truck not firing. On. A 1991. SERRIA 1500 TRUCK 5.0 LITER

Several things can cause this problem, cracked distributor cap, old ignition rotor. Or if you have coil packs, cracked coil pack, ignition control module, crank position sensor, cam position sensor. Coil pack parts and sensors can be checked by autozone, cap and rotor will have corrosion on the rotor, however a small crack in the distributor cap can be next to impossible to see, replacement is usually best option.

Feb 16, 2012 | 2000 GMC New Sierra 1500

1 Answer

I have a 1997 gmc serria 1500 ext. cab and the headlights never turn off and there are times were i would like to have them off please help

Providing you use your emergency brake on occassion, if not dont try it,it may stick. If you click down on emergency brake pedal slightly only 2 clicks it will turn off the headlights

Nov 02, 2010 | GMC C1500 Cars & Trucks

1 Answer



Jul 25, 2010 | 2002 GMC Sierra 1500

1 Answer

2000 gmc serria the abs lights came on

need to have ABS system checked to get a trouble code to many thinks to guess at you can still drive just ABS system will not work with light on

Feb 05, 2010 | 2000 GMC New Sierra 1500

1 Answer

Shifting problems on an 85 gmc auto trans

transmission is shot clutches are worn out

Oct 14, 2009 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
1993 GMC Sierra C2500 Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides