Question about Pontiac Montana

3 Answers

Diagram of how to put a serpentine belt on a 1999 pontiac montana?

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Hope this helps you.3.4L engine.


diagram of how to put - dd68fbc.gif

Posted on Aug 30, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 385 Answers

There was a diagram under the hood, perhaps on the fan shroud or fender well. any auto parts store will print one out for you.

Posted on Aug 30, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that has over 500 points.

  • Master
  • 449 Answers

A diagram should be under the hood of the car

Posted on Aug 30, 2010

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: serpentine belt

When you open the hood there is a diagram on a sticker that shows exactly how to do this. Should be on the front lip or the side of the engine compartment. You have to make sure you get it lined back up right and remember to check it once the engine has been started and make sure it running on all the pulleys correctly.

Here is a good diagram that should be able to help in case your sticker was damaged or removed. Good luck!

http://www.2carpros.com/car_repair_information/tec_info/1999/pontiac/grand_am/1999_pontiac_grand%20am_drive_belt_routing_diagram.htm

Posted on Nov 11, 2008

  • 1757 Answers

SOURCE: need a diagram for Serpentine Belt for 2001

My apologies for the delayed response.
I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.

I do not know if you still need this information, but I am answering it anyway.

CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks.
http://www.2carpros.com/car_repair_information/year/2001/make/pontiac/model/montana/2001_pontiac_montana_drive_belt_routing_diagram.htm

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a serpentine belt diagram for a 2000 Pontiac montana


Usually the belt diagrams are under the hood or near the radiator in many cars. However, if you type "2000 pontiac montana belt routing" into Google, you will find the diagram.

Apr 17, 2015 | 2000 Pontiac Montana

1 Answer

What would cause whistling noise near pully and belt area noise gets louder with acceleration


The engine serpentine belt may be worn or wet. The belt slips, causing a high pitched squealing or whistle noise. The other possiblility is a bearing beginning to go out on one of your belt driven components

Mar 27, 2012 | 1999 Pontiac Montana

1 Answer

I replaced the power steering pump on mt 2000 montana and it keeps throwing the belt off..why?


pulley on which belt is routed is worn out or belt is not original.But original parts and see if that makes a difference.Or the belt is not getting routed properly.

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 15, 2012 | 1999 Pontiac Montana

1 Answer

Serpentine belt and belt tensioner replacement


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 15, 2012 | 1999 Pontiac Montana

1 Answer

(1999 pontiac grand prix 3100 v6) how do I remove and replace my serpentine belt successfully?


Instructions Things You'll Need
  • 3/8-inch drive breaker bar
  • Metric socket kit
  • New serpentine belt
    • 1

      Park the Pontiac in a safe work area and open the hood.

    • 2

      Inspect the top of the black plastic cover that surrounds the fan for the serpentine belt routing diagram. This diagram has the instructions for installing the new serpentine belt around the accessory pulleys.

    • 3

      Inspect the front of the engine and locate the automatic belt tensioner. The tensioner on the 1999 Pontiac model vehicles is located between the alternator and the crankshaft pulley. The tensioner has a pulley on one end with a bolt head in the center of the pulley. Use the bolt head to rotate the tensioner.

    • 4

      Turn the tensioner counterclockwise with the breaker bar and a metric socket. Pull the belt out from under the tensioner pulley with your other hand. Then, slowly let the tensioner retract until it stops.

    • 5

      Pull the belt out of the other remaining pulleys. Then, pull the belt out of the engine bay and lay it on the ground.

    • 6

      Route the new belt around the crankshaft pulley. Then, route the new belt around the other remaining pullleys by using the serpentine belt routing diagram for instructions.

    • 7

      Rotate the tensioner pulley counterclockwise with the breaker bar and socket. Then, slide the new belt under the tensioner pulley. Slowly let the tensioner retract until it stops. The tensioner pulls all of the slack out of the belt and brings the new belt to the proper tension. Remove the breaker bar and socket from the tensioner pulley.

    • 8

      Inspect the new belt to ensure that it is seated inside of all the accessory pulleys as directed by the diagram. Then, crank the engine and allow it to run for about 15 seconds. Turn the engine off. Inspect the belt again once more to ensure that
      the belt is still around each pulley. Close the hood.



May 22, 2011 | 1999 Pontiac Grand Prix

1 Answer

How do i install serpentine belt on 1999 Gran Am Se 3.4l engine


Click on the following Link. It has the Serpentine Belt you will need.

The standard rule to removal the Serpentine Belt:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Rotate/Move the Tensioner away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.

3. Remove the loosened belt off one of the other more easily accessed Pulleys.

http://www.2carpros.com/car_repair_information/year/1999/make/pontiac/model/grand_am/1999_pontiac_grand_am_drive_belt_routing_diagram.htm

Standard Rule for putting it back on:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Mar 01, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Need to replace drive belt on a 1999 pontiac montana. Need routing diagrame


The belt routing is usually on a sticker under the hood.Sometimes on the plastic shield over the water pump.If it is not there then go to Auto Zone website and sign up.It`s free.You can get all sorts of repair info and how to info.Hope this helps.

Dec 16, 2009 | 2006 Pontiac Montana SV6

1 Answer

How do you replace a fan belt on a 2004 pontiac montana


Here's a series of videos that explains how to replace the serpentine belt on your 2004 Montana.

http://www.wonderhowto.com/how-to/video/how-to-change-a-serpentine-belt-on-your-car-39904/

Here's a diagram to help you remember how to rout the new belt...

6f452ae.jpg

Nov 30, 2009 | 2004 Pontiac Montana

1 Answer

Need a diagram for Serpentine Belt for 2001 Pontiac Montana


My apologies for the delayed response.
I am going back to answer - unanswered questions. I have only been on this site for the past 4-months. Questions Posted have exploded (+55%) since joining.

I do not know if you still need this information, but I am answering it anyway.

CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks.
http://www.2carpros.com/car_repair_information/year/2001/make/pontiac/model/montana/2001_pontiac_montana_drive_belt_routing_diagram.htm

Oct 27, 2009 | 2001 Pontiac Montana

1 Answer

Serpentine belt


When you open the hood there is a diagram on a sticker that shows exactly how to do this. Should be on the front lip or the side of the engine compartment. You have to make sure you get it lined back up right and remember to check it once the engine has been started and make sure it running on all the pulleys correctly.

Here is a good diagram that should be able to help in case your sticker was damaged or removed. Good luck!

http://www.2carpros.com/car_repair_information/tec_info/1999/pontiac/grand_am/1999_pontiac_grand%20am_drive_belt_routing_diagram.htm

Nov 09, 2008 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...