Question about 1992 Dodge Dakota

1 Answer

Where is the crankshaft position sensor located

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 385 Answers

Look for a very small sensor with 2 or 3 wires coming from it. usually on the side of the harmonic balancer pulley in a bracket. don't confuse it with the camshaft position sensor usually located more on top of that pulley below the end of the camshaft. any auto parts store can tell you or even show you where it is at.

Posted on Aug 30, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

on the engine where is the camshaft position sensor located

Posted on May 17, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the Crankshaft Position Sensor location on a Town and Country with the 3.6L V6 engine?


The role of the crankshaft position sensor is to determine the position of the crankshaft, the crankshaft angle. It is usually with a camshaft position sensor work together - to determine the basic ignition timing. Car Diagnostic Tool

Aug 27, 2016 | 2011 Chrysler Town and Country

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

WHERE IS THE CRANK SHAFT SENCER LOCATED ON THE MOTOR


The 2 crankshaft sensors are located on the front of the engine block, between cylinder Numbers 4 and 6. Crankshaft position A sensor is located on the upper crankcase and crankshaft position B sensor is located in the lower crankcase. Both sensors extend into the crankcase and are sealed into the engine block with O-rings. The crankshaft position sensors are not adjustable.

Jun 08, 2010 | 1998 Cadillac Catera

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

3 Answers

Crankshaft position sensor location on 2004 chrystler pacifica


can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

May 02, 2009 | Chrysler Pacifica Cars & Trucks

1 Answer

I CANT LOCATE CRANK POSITION SENSOR


7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
Right hand side of engine, at end of crankshaft, behind harmonic balancer

Apr 12, 2009 | 1995 Chevrolet Monte Carlo

1 Answer

04 Dodge SRT 4 crankshaft sensor


The Crankshaft Position Sensor is located directly next to the starter.
  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Aug 15, 2008 | 2004 Dodge SRT-4

Not finding what you are looking for?
1992 Dodge Dakota Logo

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...