Question about 1999 Dodge Durango

1 Answer

What is the 3 way connector called for the washer fluid lines and where do I get one

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 662 Answers

It is simply called a T-connector, and is mostly available from most auto parts stores......

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windship wiper spray won't spray


Provided there is washer fluid, it may be frozen, the line may be unhooked/ pinched, the power may not be getting to the pump, the pump could be shot,. are you hearing any noise when making a call for washer fluid?
Best regards
Ck

Feb 13, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

The winshield washer fluid won't work, but it sounds like I can hear the little motor when I push the end of the wiper blade switch


Push the washer fluid button and hold it for 20 sec then look under the truck and seeif you see the washer fluid dripping on to the ground, if theres no sign of the washer fluid then you have a bad washer pump, which is located on the side of the washer bottle, if theres fluid dripping then you will need to follow the line, start at the washer nozzles, this is where it breaks the most, if the line is plastic you can use a peice of rubber hose that size and connect the broken line back together with the hose, hope this helps.

Nov 10, 2010 | 2004 Dodge Ram 1500

1 Answer

Replace windshield reservoir


Windshield Washer Motor REMOVAL & INSTALLATION 1987-95 Vehicles
  1. Disconnect the negative battery cable.
  2. Drain or siphon the washer solvent from the reservoir.
  3. For 1987-91 vehicles, remove the brace.
  4. Unfasten the reservoir screws.
  5. Detach the electrical connectors and washer hose.
  6. If necessary, remove the reservoir from the vehicle.
  7. Remove the washer pump motor from the reservoir. Fig. 1: Location of the windshield washer fluid reservoir and pump - 1987-91 vehicles 89636g50.gif
    To install:
  8. Install the washer pump motor on the reservoir. Make sure the pump is fully seated in the reservoir gasket.
  9. Position the reservoir in the vehicle.
  10. Attach the electrical connectors and washer hose.
  11. Install the reservoir retaining screws.
  12. Install the brace.
  13. Fill the reservoir with washer solvent.
  14. Connect the negative battery cable, then check for proper washer pump operation.
1996-99 Vehicles
  1. Disconnect the negative battery cable.
  2. Drain or siphon the washer solvent from the reservoir.
  3. Detach the electrical connectors from the washer.
  4. Disconnect the hose from the washer pump.
  5. Loosen the nut at the bottom of the washer reservoir.
  6. Unfasten the 2 nuts, then remove the washer solvent reservoir.
  7. Remove the washer pump from the container.
  8. If necessary, remove the solvent lever sensor switch from the washer solvent container. Fig. 2: Exploded view of the washer fluid reservoir, pump and level sensor 89636g51.gif
    To install:
  9. Install the solvent level sensor switch in the washer solvent container. The tab on the solvent level sender switch must be lined up with the slot in the hole.
  10. Install the washer pump into the reservoir, making sure the pump is pushed all the way into the container seal.
  11. Install the washer solvent reservoir and secure with the 3 nuts. Tighten the nuts to 44 inch lbs. (5 Nm).
  12. Attach the electrical connectors to the solvent level sensor and washer pump.
  13. Connect the hose to the washer pump.
  14. Fill the reservoir with washer solvent.
  15. Connect the negative battery cable, then check for proper washer pump operation.
prev.gif next.gif

Nov 09, 2010 | 1997 Pontiac Bonneville

1 Answer

2002 nissan sentra windshield washer fluid not working.


Assuming the reservoir has washer fluid in it - when you activate the washers with the key on do you hear a hum from the pump? When you activate it do you see fluid coming out under the car? If any of the lines are damaged the fluid may not be travelling where you want it to. If the pump is not working altogether check to make sure the wire is plugged onto it. Check the tubing from the pump to the connector under the hood. If your fuses are good and the pump is not working at all have the plug checked for power. Pumps go out, but the cause is usually something more simple and less expensive.

Dec 17, 2009 | 1995 Nissan Sentra

1 Answer

Rear windshield squirter does not work


Check the connector and the washer fluid pump for power at your washer fluid pump by your washer bottle. Hook up a test light to both connectors.

Nov 25, 2009 | 1999 GMC Jimmy

1 Answer

My windshield washer fluid is not pumping out to the back and front, the fluid tank is full


Remove the small tube that's attached to the fluid tank and press the wash button.
1 - If fluid isn't gushing out take out the connector to the pump and connect a light bulb to it. If the bulb lights up when you press the button the pump either is busted (replace it) or its connectors are corroded (clean them).
2 - if the fluid is gushing out then it's a blockage somewhere down the line; put the tube back in the tank, find and disconnect the other end, press the button. If it doesn't work then you have found the culprit - replace it. If it does flow then continue till you locate the blocked part.

Nov 23, 2009 | 2006 Kia Sorento

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Front washer fluid does not pump, rear one does


Sounds like the pump is nacked. Or it may be a wiring earth fault. Find the wiring connector get a earth/Grong test light. Connect it to the positive and a good earth point on the car have some one work the stalk in the car and see if you got power if not it ll be the fuse, the pump or a busted wire in the line

May 12, 2009 | 2002 Lincoln Navigator

1 Answer

Removing the windshield washer reservoir in a 2002 Chrysler T&C


REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the engine fresh air housing inside the engine compartment.
  3. Disconnect the washer hose at the in-line connector forward of the cowl grille so that the in-line connector remains with the washer hose from the fresh air plenum.
  4. Disconnect the washer hose from the hose clip located on the front fender side shield.
  5. Remove the filler tube screw.
  6. Hoist and support vehicle on hoist or jack stands.
  7. Remove the right front wheel and tire assembly.
  8. Disconnect the left right front wheelhouse splash shield and move aside.
  9. Drain washer fluid from the reservoir and into a suitable clean container. This can be done by disconnecting the windshield washer hose from the front (outboard) washer pump and allowing the washer fluid to drain into a container through a temporary jumper hose connected to the front washer pump.
  10. Disconnect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the release position, then, depress the black tab and pull the connector off the pump or sensor.
  11. Remove the two reservoir mounting screws.
  12. Disconnect the reservoir from the body mount by raising the reservoir upward slightly and then down so that the reservoir filler neck and front washer hose pull through the opening in the front fender side shield.
INSTALLATION

  1. Push filler neck and front washer hose through the opening in the front fender side shield. Connect the reservoir to the body mount by lowering the reservoir down.
  2. Install the two reservoir mounting screws. Torque screws to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  3. Connect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the closed or locked position.
  4. Assure that washer is properly routed to prevent pinching and possible inoperative washers.
  5. Connect the left right front wheelhouse splash shield and move aside.
  6. Install the right front wheel and tire assembly.
  7. lower vehicle from hoist or jack stands.
  8. Install the filler tube screw. Torque screw to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  9. Connect the washer hose to the hose clip located on the front fender side shield.
  10. Connect the washer hose at the in-line connector forward of the cowl grille.
  11. Install the engine fresh air housing inside the engine compartment.
  12. Connect the battery negative cable.
  13. Verify system operation.

Apr 01, 2009 | 2002 Chrysler Town & Country

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...