Question about 1995 Geo Metro

Open Question

Need a vacuum hose diagram for a '95 Geo Metro 1.3 litre, as the head gasket was replaced and the vacuum hoses aren't quite right. The car will start, idle, then, stall...

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 95 geo metro

i need a fuse diagram for a 1995 geo

Posted on Sep 28, 2008

  • 25 Answers

SOURCE: stalling no idle

Hi,if you want to now where is a leak ,start the car if is possible and spry the hosing pipes wen suddenly rpm increase you now where is the problem or ken be the trottle body!

Posted on Jan 16, 2009

jpstuhr
  • 49 Answers

SOURCE: need to replace 95 Geo front turn signal bulb

Here's a diagram

b0bc01b.jpg

Posted on Feb 12, 2009

emissionwiz
  • 75817 Answers

SOURCE: When i start my 1997 Geo Metro, it often sputters

Try this
Here are the most common causes of surges, stalls at stops, low erratic idle speed, rough idle and engine hesitation, it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Posted on Apr 03, 2009

  • 2841 Answers

SOURCE: How do I check my vacuum hoses in my 95 Jeep

The easiest way is to start the engine and spray carburetor cleaner at each connection. When you hear the engine RPMs increase you have found a leak. On a 15 year old car I would just replace all under-hood vacuum hoses. Replace them one at a time as to not get confused. Just buy enough hose of each size to replace them all. Cut them to length one at a time.

Posted on Jun 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On a 95 Geo metro the evap canister has a bottom hose where does it go to


Are you referring to the charcoal canister? That hose is not connected to anything. It's purpose is to suck in air when needed and expel fumes when needed.

Feb 20, 2016 | Geo Cars & Trucks

2 Answers

1990 Geo metro popped and poured white smoke out


its a GEO POPPER.
"no oil up on crank case"

no idea what that means.??????
yes PCV valve. do clog.

white smoke at end if tail pipe.
you didnt say where,?

white smoke has 2 reasons.(tail end)
Steam and oil.
steam goes away fast and looks just like moms tea pot. and smells sweet, like the antifreeze in engine. (rad cap off ,sniff sniff, cold engine)

oil burning, smoke is very very slow to go away.
and smells like , blush burned oil.
if not sure what burn oil looks like or smells like
take out the dip stick on a hot engine
let it drip to the hot exhaust manifold there.
now you know. and is a key diagnostic skill.


no oil seen on dip stick end?, you mean that?
well you need to keep that from happening,
doing weekly service, and for sure old cars.
26 years old.

low oil invites blowing up a good engine.
for sure.
if it did that smoke is oil
if it did 10x worse, both .

my wild guess is you meant to say
I didnt see oil leaking on top of engine.
right?

if the engine backwires to the air cleaner
you forgot to replace the cam belt every 60k miles
the pcv will also be clogged, on cars not getting proper service, super colon.
if the PCV clogs,engine may leak oil bad.

this engine btw is a G10 3 cylinder.
with TBI injection.
we can talk TBI all day, owned one.

white smoke can come from many places
exhaust manifold, leaks of oil can land there
engine can back fire to air cleaner making smoke.
tail end.
steam is much worse. ill not delve in to that yet/.

Apr 04, 2014 | 1990 Geo Metro

1 Answer

1995 Geo Metro Head Gasket Leaking Coolant


best to change the headgasket n be done with it

Jan 02, 2014 | Geo Metro Cars & Trucks

1 Answer

Antifreeze is leaking from back of motor on a 1995 geo metro manual trans


only you can park start engine, warm it up, and at normal
hot 14psi coolant pressure, see the exact leak point, not me or anyone here can. its an EYEs on thing,
the object leaking is bad. if a hose, flange or gasket, if the
head gasket leaks, then bingo bad head gasket.

Oct 22, 2013 | 1991 Geo Metro

1 Answer

How do i chage the fuel injector for a geo metro 1997 LSI?


REMOVAL & INSTALLATION Fig. 1: Removing injectors from fuel rail 84245032.gif
Fig. 2: Make sure injectors rotate freely in cylinder head 84245033.gif
  1. Relieve fuel system pressure and disconnect the negative battery cable.
  2. Remove intake air hose between throttle body and intercooler.
  3. Remove accelerator cable.
  4. Unclamp PCV and fuel return hoses from deliver pipe.
  5. Unclamp injector wiring harness.
  6. Disconnect injector coupler.
  7. Remove cold start injector pipe from delivery pipe.
  8. Remove vacuum hose from pressure regulator.
  9. Remove fuel feed hose from delivery pipe.
  10. Remove pressure regulator from delivery pipe.
  11. Remove delivery pipe with injectors.
  12. Remove injectors from delivery pipe. To install:
  13. Replace injector O-rings and lubricate with fuel. NOTE: Make sure injectors rotate smoothly. If not, probable cause is incorrect installation of O-ring.
  14. Check if insulator is scored or damaged. If it is, replace with new one.
  15. Connect delivery pipe with injectors.
  16. Install pressure regulator to delivery pipe using a new O-ring.
  17. Install fuel feed hose to delivery pipe.
  18. Install vacuum and fuel return hoses to pressure regulator and clamp securely.
  19. Install cold start injector pipe to delivery pipe using new gaskets.
  20. Install injector coupler. Clamp injector wiring harness.
  21. Install PCV hose to cylinder head.
  22. Install throttle position sensor coupler.
  23. Install accelerator cable and adjust free-play.
  24. Install intake air hose to throttle body and intercooler.
  25. Connect the negative battery cable.
  26. Start engine and check for leaks.
prev.gif next.gif

Jul 03, 2010 | 1997 Geo Metro

1 Answer

95 geo metro 3cyl. 1.0L no spark changed


Pull one or two sparkplugs and check them for moisture; not fuel, but for water beads.
I don't know how long your engine ran after losing coolant but there is a chance that you lost the head gasket and have gotten water into the cylinders.

Nov 26, 2009 | 1992 Geo Tracker

1 Answer

I dont have a repair manual,need degrees BTDC Please


The timing on your car should be at 6° BTDC. The thing is, Do you have a vacuum advance or electronic advance? With vacuum you would unplug the hose to the distributor and plug it.(LSI) If it has two hoses to the advance it would be the outside hose. I assume you are using an inductive timing light with an inductive clamp that attaches to #1 plug wire.
With electronic ignition you must unplug the diagnostic connector located next to the ignition coil. Then use a jumper wire between the bottom to terminals on the plug. Top being with the plug latch facing up. See what you find. Good luck.

Apr 01, 2009 | 1989 Geo Metro

1 Answer

Ignition timing for 1991 Pontiac Firefly or 1991 Chevrolet Sprint or 1991 Geo Metro


for 1991 geo metro 1.0 liter 3 cyl engine the timing is 6 degrees before top dead center. you will need a tachometer because the rpm must be 800 when you set the timing. also you will need to disconnect the vacuum advance to the distributor, and plug the hose to avoid a vacuum leak. (alternate method is to pinch the vacuum advance hose going to the distributor while you are setting the timing) Good Luck!

Oct 28, 2008 | 1991 Geo Metro

Not finding what you are looking for?
1995 Geo Metro Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...