Question about 2005 Chrysler 300

1 Answer

Have a chrysler 300 2005 with 2.7 liter engine. To replace the knock sensor does the head have to be removed?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 361 Answers

No the intake

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knock sensor for 2007 Saturn outlook. I can't pass emissions test!


Check engine light on ? What code ? There are many different (DTC'S) - diagnostic trouble codes that can set for knock sensors ! There all don't mean that you replace the sensor .
DTC P0324: Knock Sensor (KS) Module Performance
DTC P0325: Knock Sensor (KS) Circuit Bank 1
DTC P0326: Knock Sensor (KS) Performance
DTC P0327: Knock Sensor (KS) Circuit Low Bank 1
DTC P0328: Knock Sensor (KS) Circuit High Bank 1
DTC P0330: Knock Sensor (KS) Circuit Bank 2
DTC P0332: Knock Sensor (KS) Circuit Low Bank 2
DTC P0333: Knock Sensor (KS) Circuit High Bank 2

The knock sensor (KS) system enables the control module to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The sensors are located below each cylinder head on the engine block. The KS produces an AC voltage signal that varies depending on the vibration level during engine operation. The control module adjusts the spark timing based on the amplitude and the frequency of the KS signal. The control module receives the KS signal through 2 isolated signal circuits. The control module learns a minimum KS noise level at idle and uses calibrated values for the rest of the RPM range. The control module should monitor a normal KS signal within the noise channel.
Knock Sensor Replacement - Bank 1
Remove the exhaust manifold lower heat shield. Refer to Exhaust Manifold Lower Heat Shield Replacement.
Disconnect the engine wiring harness electrical connector (1) from the bank 1 knock sensor (2).
Loosen the knock sensor bolt and remove the knock sensor.
Knock Sensor Replacement - Bank 2
Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
Remove the engine oil filter. Refer to Engine Oil and Oil Filter Replacement .
Lower the vehicle.
Disconnect the engine wiring harness electrical connector (2) from the bank 2 knock sensor (3).
Loosen the knock sensor bolt and remove the knock sensor.

Nov 12, 2016 | Saturn Cars & Trucks

1 Answer

2005 Sebring Touring 2.7. Where is the knock sensor located?


This knock sensor is very difficult to access. It is located between the two cylinder banks, it screws into the cylinder block underneath the intake manifold.

In order to remove the sensor the intake manifold and right cylinder head must be removed.

Nate

Aug 23, 2015 | Chrysler Sebring Cars & Trucks

2 Answers

Knock sensor diagram


On the 2.4 liter four-cylinder engine it is located on the siie of the engine block (the side nearest the firewall).

On the 3.0 Liter V-6 engine there are 2 knock sensors and the are located in the "valley" below the intake manifold. You'll have to remove the intake manifold to get to them.

Jul 22, 2014 | 2003 Toyota Camry

1 Answer

Gmc Sierra knock sensor???


There a several different engine sizes. The most common is the 5.3 liter. To replace the knock sensors (which will not solve your engine noise at startup) you will need to first remove the intake plenum. That is the part in between the valve covers that the throttle body and the injectors are attached to. Once the intake plenum is removed you ill see the knock sensors bolted to the block.

Apr 12, 2013 | Cars & Trucks

2 Answers

How do you replace a Nissan 350Z knock sensor?


Hello
The knock sensors (one for each cylinder head on the V6) are located on the inside of the cylinder heads, in order to replace them the upper intake manifold must be removed. It is always recommended on this engine family that not only replace the 2 knock sensors but that you also replace the short sub wiring harness to the knock sensors from the main engine harness as it is many times the a common cause of the knock sensor code(s) in the 1st place.

Oct 31, 2011 | 2003 Nissan 350Z

1 Answer

1999 300M the engine is knocking. It also shuts off in mid drive


There is a Knock Sensor (1) on this engine, but is in the center of the engine UNDER the intake manifold on the block (in the valley, the valley so low). Check the values of the voltage in a Chiltons or OEM book and unplug it from the rear and test it before you remove it. (Quite a job removing the plenum, wires, Manifold and finally the knock sensor (about 75 bucks in the Midwest at a parts store). If so, you are lucky in a 3.3L you have to remove a HEAD.

Sep 07, 2011 | 1999 Chrysler 300M

1 Answer

Where is the knock sensor located on a 2000 ford taurus with a 3.0 liter 6 cyl pushrod engine?


I could not find a knock sensor on the 3.0L 6 cyl engine in my online resource. There were lots of other sensors, though.

If it had one like a GM, then it would be located on the cylinder head or block somewhere.

Does this help?

Sep 09, 2010 | Ford Taurus Cars & Trucks

1 Answer

Where is the location of the knock sensor for a 2005 HD 2500 6.0


HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Jan 26, 2009 | 2000 Chevrolet 2500

2 Answers

Knock sensor


The knock sensor threads into the side of the cylinder block.
  1. Disconnect electrical connector from knock sensor.
  2. Use a crow foot socket to remove the knock sensors.
INSTALLATION
The knock sensor threads into the side of the cylinder block in front of the starter.

  1. Install knock sensor. Tighten knock sensor to 10 Nm (7 ft. lbs.) torque. Over or under tightening effects knock sensor performance, possibly causing improper spark control.
  2. Attach electrical connector to knock sensor

May 15, 2008 | 2005 Chrysler Sebring Conv

Not finding what you are looking for?
2005 Chrysler 300 Logo

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...