Question about 2003 Isuzu Axiom

1 Answer

How can I remove a tail light assembly to replace a lamp?

The screws come out fine but there appears to be something holding the assembly on that we can't get it to come loose.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 20,706 Answers

Posted by Pmlove509 on Aug 30, 2010

James spams again.

Posted on Dec 01, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: tail light bulb out

If you are still interested I figured it out this morning.

1. Remove the obvious 2 rear screws.
2. With a padded or rubber tipped flat tool gently pull towards the side of the car and pry off.
(I used a butter knife and cloth between it and the car)

There are 2 rods that insert into receivers on the side of the car. The real trick is that it does not pull off towards the rear as you would expect, it pulls off to the side.

If you still have trouble post here and I'll put up a demo video.


T

Posted on Jan 22, 2009

  • 496 Answers

SOURCE: removing rear light assembly on honda odyssey 2006

Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Posted on Jan 24, 2009

  • 375 Answers

SOURCE: isuzu axiom pull camper

As I recall, your Axiom has a Tow Rating of 5000 pounds -- but check your Owner's Manual to be sure. I have several friends who tow with their Isuzus (using 1st and 2nd Gen model Troopers and Rodeos) and pull pop-up campers, high-profile campers, ATV trailers, etc... There's even even one guy who pulls his Trail Rig (another Isusu) to various off-road events on an 18-foot tandem axle steel frame trailer -- All of them do so without any problem whatsoever. The thing is, all of them use a Load Distributing Hitch System, such as this: http://www.truckaddons.com/Catalog/subpages/hidden-hitch-weight-distributing-hitch-systems.htm It makes a HUGE difference. Hope this helps.

Posted on May 18, 2008

  • 2 Answers

SOURCE: how to replace tail/stop light for a 2002 isuzu axiom

remove the hardware (2 bolts) then wiggle to loosen, now pull outwards (pull somewhat hard) towards the sides to clear some kind of guide. Then towards the rear<

Posted on Apr 13, 2009

goofduck
  • 490 Answers

SOURCE: remove tail light assembly

there are plastic clips on it just take your time and they will come out

Posted on Apr 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace brake light bulb audi a4 1.8t 2002


Start by opening the trunk lid. On the sides of the trunk, just beside where the trunk lid sits when closed there is a circle cap on either side. Remove the cap it is the same material as the trunk side trim (fuzzy carpet) then there will be a screw set into the hole that you just uncovered. You can use either a philips screw driver or an 8mm socket and remove the screw/bolt. you may need to reach in with a set of needle nose pliers to remove the screw after it is loosened all the way. Once the screw is removed grab the tail lamp assembly from the inside and twist the tail lamp out of the holding pins located on the side edge of the tail lamp. The whole light will come off of the body in your hands. Once the tail lamp assembly is out there is an access panel on the back side where all the bulbs are installed. Depress the two holding tabs on the sides and carefully remove the bulb holder. Then replace any blown bulbs and reinstall.

Jan 17, 2014 | 2006 Chrysler PT Cruiser

1 Answer

License plate bulb replacement on a 2002 Buick LeSabre I don't have screws holding the bulb assembly in place. It appears to be in place with tabs larger than the assembly holding the assembly in...


Hi, my name is John I will do my best to assist you.

The entire tail/backup lens assembly has to be removed from the trunk lid as shown in the drawing attached. There will most likely be some nut's or clip's on the assemblies mounting pins on the inside of the trunk lid.
  1. Disconnect the tail/back up lamp harness connector from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.
  5. Installation is the reverse of removal.

tecnovative_128.gif
If you have more specific questions please post comments to this thread and I will endeavor to monitor new activity and respond as soon as possible. I recommend that you "bookmark", or "add to favorites" this page for your convenience.

Feb 15, 2011 | 2002 Buick LeSabre

1 Answer

How to change break lights


Tail Lights
  1. Open the endgate or liftgate.

  2. Remove the screws that retain the tail lamp assembly to the vehicle.
    32085_blaz_g0151.gif

    Tail lamp assembly removal

  3. Rotate the bulb sockets 1/4turn counter-clockwise in order to remove the bulb sockets from the tail lamp assembly.

  4. Remove the bulbs from the sockets.

To install:

  1. Install the bulbs into the sockets.

  2. Install the bulb sockets to the tail lamp assembly by rotating the sockets1/4 turn clockwise.

  3. Install the tail lamp assembly to the vehicle.

  4. Install the screws that retain the tail lamp assembly to the vehicle. Tighten the screws to 17 inch lbs. (1.9 Nm).

Oct 23, 2010 | 2000 Oldsmobile Bravada

1 Answer

Need to replace stop light


Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif

Oct 18, 2010 | 2004 GMC Envoy

2 Answers

Having trouble fixing brake lights


Tail/Turn Signal Lamp Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Oct 13, 2010 | 1997 GMC Sierra

2 Answers

How do I replace a burned out backup light on a 1998 cheverolet silverado c-1500 pickup truck?


Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Jul 17, 2010 | 1998 Chevrolet C1500

1 Answer

How do I replace the brake lamp on an 89 Ford Tempo XL?


Open the trunk and remove clips that hold carpet in place around the trunk latch. Remove the screw caps that hold tail light inplace and slide light assembly out. Careful NOT to pull too hard on assembly to avoid damage to wires. Squeeze clips and turn lamp socket and pull out. Replace bulb. Installation of light assembly is reverse of removal. Be sure to replace all screw caps on light assembly.

Feb 15, 2010 | 1989 Ford Tempo

1 Answer

How do you remove the lower tail lamp assembly to


i thought you replaced the bulbs from the inside, look on the inside for a plastic cover over the bulb recepticals, take off cover you should see the bulb sockets, twist 1/8 to a 1/4 turn counterclockwise,it should come right out,luck

Jan 31, 2010 | 2004 Kia Sorento

2 Answers

Removing rear light assembly on honda odyssey 2006


Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.

-T

Jan 24, 2009 | 2007 Honda Odyssey

2 Answers

Process to get to tail light bulb for replacement on 99 rav4. Do you have to remove the paneling in the rear compartment?


Well, this is rather embarassing but I simple decided to look through the owners manual thinking that they usually don't contain that sort of thing and there I found. Pictures and a description of the process. Very simple...remove a phillips screw to remove a small plate covering the 2 screws that hold the tail light assembly in place. Remove the 2 screws and pull our the assembly and replace the bulb. Duh....I thought with Toyota engineering, they wouldn't make replacing a bulb a major project. Thanks for checking back....Allen

Aug 05, 2008 | 1999 Toyota RAV4

Not finding what you are looking for?
2003 Isuzu Axiom Logo

Related Topics:

930 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...