Question about Mitsubishi Galant

Open Question

How do you remove a starter on a 2003 galant 3.0 dohc

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changhing valve cover gasket 03 mitz galant 3.0 v6


  1. Disconnect the negative battery cable.
  2. Remove the upper intake manifold.
  3. On the 3.0L DOHC engine, remove the ignition wire cover.
  4. Remove the ignition wires and spark plugs.
  5. Remove the crankcase ventilation tubes from both valve covers.
  6. Remove the retaining nuts and engine wiring from both valve covers and move aside.
  7. Remove the valve cover retaining bolts and studs.
  8. Remove both valve covers from the engine.
To install:
  1. Clean the valve cover gasket sealing surfaces.
  2. Install new valve cover gaskets onto the valve covers.
  3. Place the valve covers into position.
  4. Reinstall the valve cover retaining bolts and studs and tighten in sequence to:

    3.0L SOHC engine: 7 ft. lbs. (9 Nm)3.0L DOHC engine: 42-54 inch lbs. (4-5 Nm)3.5L engine: 30 inch lbs. (3 Nm)
  5. Install the engine wiring and tighten the retaining nuts.
  6. Install the crankcase ventilation tubes into both valve covers.
  7. Install the ignition wire separators, the ignition wires, and the spark plugs.
  8. On the 3.0L DOHC engine, install the ignition wire cover.
  9. Install the upper intake manifold as described in this section.
  10. Connect the negative battery cable.
  11. Run the engine and check for leaks and proper operation.

Jun 25, 2017 | Cars & Trucks

2 Answers

Im replacing the starter on my 1995 mitsubishi galant. I need a picture of the wire hookup to the starter.....you know, which wire goes to the negative and so forth


this might help...Same concept ..3 wires http://www.google.com/search?q=how+to+install+a+1995+mitsubishi+galant+starter&um=1&hl=en&source=lnms&sa=X&ei=TO4OUqrrHMaB2gXtmYCgAw&ved=0CAgQ_AUoAA&biw=1024&bih=672#bav=on.2,or.&fp=1cb0759d76b6b3f9&hl=en&q=1995+mitsubishi+galant+how+to+replace+the+starter+

Aug 17, 2013 | Cars & Trucks

2 Answers

Where is 2004 mitsubishi galant starter located at?


michael_cass_481.jpgmichael_cass_482.jpgThes are on a 2.4L and 3.8L did not know what motor you had? So i gave you both...

Jul 30, 2011 | 2004 Mitsubishi Galant

1 Answer

Where is the starter solenoid on a 2003 Mitsubishi Galant


It is located on the starter. I have included a picture of the 2003 galant starter showing which portion is the solenoid.

-Ben

9_14_2011_9_28_28_pm.jpg

Mar 18, 2011 | 2003 Mitsubishi Galant

3 Answers

I have a 2003 Galant GTZ 3.0L . batery is good and all the lights work. when I try to start the car all I hear is single click. the car does not start. I cleaned the batery cables and still the same, no...


if you've tested your battery and know you have a good connection at the terminals that one click sound is a bad starter. you may wish to attempt to tap on it while cranking to try to get it to start. if you do crawl under your car use jack stands to hold the car in the air. never leave a losd on the jack. safety first. if this was helpful please leave positive rating.

Nov 30, 2010 | 2003 Mitsubishi Galant

1 Answer

Trying to remove the starter on a 1991 SaturnSL


no there is not a special tool need more info go to collisionrepairadvice.com for more
1991 Saturn SL L4-1.9L DOHC VIN 7 Vehicle Level a_003366.gif Starting and Charging a_003366.gif Starting System a_003366.gif Starter Motor arrow1.gif Service and Repair arrow2.gif blnk_spc.gif Service and Repair Notes
  1. Disconnect battery ground cable.
  2. Remove air inlet tube and fresh air hose, on DOHC models, lift resonator upward to disengage from engine support bracket.
  3. Remove upper starter attaching bolt through access hole near intake manifold support bracket.
  4. Raise and support vehicle.
  5. Using suitable pliers, remove starter shield pin, then lift shield upward to release from solenoid.
  6. Disconnect starter electrical connectors and position aside.
  7. Remove lower starter attaching bolt.
  8. Remove rear starter support bracket attaching bolt.
  9. Rotate starter until bracket clears axle shaft support bracket, pull rearward toward lefthand side of vehicle to remove.
  10. Reverse procedure to install. Torque starter attaching bolts to 26 ft. lbs., starter bracket bolts to 22 ft. lbs. and starter solenoid terminal to 3 ft. lbs.

Apr 11, 2009 | 1991 Saturn SL1

1 Answer

2003 Galant Clicking noise when trying to start.


It is your battery it may not be completly dead but it is too dead to run the starter. It take 300 -600 amp to run a starter and 20 amp to run a stereo

Mar 08, 2009 | 2003 Mitsubishi Galant

2 Answers

Mitsubishi Galant 1992


1992 Mitsubishi Galant
2.0 liter DOHC L492789848.gif

Aug 18, 2008 | 1992 Mitsubishi Galant

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...