Question about 2005 Scion tC

1 Answer

Grinding noise while turning the car to the right in even the slightest amount at any speed, and then when i straighten it back out the noise is almost fully gone and rides nice, no problems steering to the left

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Scion Master
  • 827 Answers

Right side cv joint is going bad, need to change both, left and right

Posted on Nov 30, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 64 Answers

SOURCE: steering not straightening out at slow speed

Worn steering components which allow the steering wheels to travel too far either way,hop underneath and get a friend to move the steering while you have a look for movement between the components, or a power steering component like relief valve. Its a bit hard to know without seeing the vehicle, i suggest a steering and suspension specialist like pedders or similar.These guys can do a safety inspection only, if you want to do the work yourself. Cheers Timo.

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grinding Noise


Try the bearing.

Mar 20, 2016 | Cars & Trucks

1 Answer

Mazda 6 grinding noise when turning


Grinding noise upon turning is normally one of two issues. First, and most often, it is caused by a worn out outer CV joint. If your vehicle has more than 50000 miles on it and the axle shafts have never been replaced, this is what I would suspect first. In addition, CV noise will be louder when turning under power (gas pedal pressed) than when coasting into a turn. The other possibility is a front wheel bearing assembly. These are not as common, but do wear out as well. The wheel bearings will usually make no noise when going straight, but will make noise upon even the slightest side to side turn. CVs on the other hand, usually grind only when going into corners or making left or right turns. If you suspect a CV joint, but don't have high mileage, you could have a torn CV boot that resulted in the grease that lubricates the joint being depleted and causing the noise. You can inspect the out boots visually for tears....grease leaking out usually leaves telltale spatters in the wheel wells also. Replacement of the CV joint can be done, but it is usually cheaper to replace the entire axle shaft as they are serviced as a unit.

Nov 03, 2013 | Mazda MAZDA6 Cars & Trucks

1 Answer

97 honda accord knocking and grinding noise in front end


i have a 1997 honda accord ex. i have a knocking noise in the front end up to 25mph and goes away until you hit about 55mph then it comes back but it also goes away with the slightest turn of the steering wheel. what could this be? please help me, i been stuck on this for 5 days now. thanks.

Apr 17, 2012 | Cars & Trucks

2 Answers

Car pulls right, terrible grinding noise from front right.


TAKE IT BACK WHERE THEY DONE THE LAST LOT OF WORK and tell them to do the complete job again as it sounds like a con job to me as a wheel aligment should last for a year a least and the grinding is in the braking system and something must still be bent ,
Its still under warranty dont pay any more..

Oct 26, 2009 | 1993 Buick Regal

1 Answer

Grinding noise when making right turns.


CV joint. Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Sep 30, 2009 | 2004 Hyundai Elantra

2 Answers

I got grinding it the front wheel bering,,but only the left


ok you have a bad right front wheel bearing by what you are describing

Sep 04, 2009 | 1997 Ford Aspire

1 Answer

Grinding noise braking at slow speed hard right turn


The problem is either a bad CV joint or is it possible that the brakes are worn.

Sep 03, 2009 | 1999 Audi A4

Not finding what you are looking for?
2005 Scion tC Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scion Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Brad Brown

Level 3 Expert

15941 Answers

Are you a Scion Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...