Question about 2002 Chevrolet Malibu

1 Answer

How to activate blink code on 2002 GM malibu with jumper wire at diagnoustic connector

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 4,336 Answers

Just get a code reader and use that.

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get flash code from ecm


ECM not TCM, got you.
the car has a connector called a DLC
data link conn.
the codes are DTCs (modern jargon) diag, trouble codes.

you jumper 2 pins, like all cars of this era. (most)
covered in the FSM book by suzuki or Geo (GM)
or at any of the 3 forums here.
http://www.fixkick.com/swift.html

the service jumper
first ill show the schematic.
http://metroxfi.com/wp-content/uploads/2008/11/6e2-a-4.png
find that connector under hood
then jumper the ppl-yell purplewithyellowstripe.
to ground
and the CEL blinks out the streams of codes. if there.

wow the whole car.

http://metroxfi.com/2008/11/geo-metro-and-suzuki-swift-wiring-diagrams/

if you use google
you will see lots of photos of the connector
geo meter service jumper
suzuki swift service jumper,
google it.

Apr 17, 2014 | 1993 Geo Metro

1 Answer

Where is diagnostic connector locationon 1994 toyota base pickup


The check engine light is used to blink out the trouble codes. The diagnostic connector is usually under the hood on driver's side, back near the firewall. Sometimes under the driver's dash. Use a jumper wire and connect terminals TE1 and T1. Then turn key to on, not start, and the check engine light will blink out the trouble codes. If no codes are present, the check engine light will stay on constantly. Remove jumper wire when diagnostics completed. To clear codes after repairs, disconnect the negative battery terminal for one minute, and then reconnect.
This site has Toyota code explanations:

Dec 30, 2013 | Cars & Trucks

1 Answer

1994 cutlass ciera s stops running after 20 minutes of driving.


The jumper goes into A & B, usually the top right two terminals. But check, in those years, GM was transitioning over to OBD-II, and they had some hybrid connectors that didn't match OBD-1 connectors. Leave it to GM for oddballing.

May 25, 2013 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Where is the diagnostic port located on an isuzu trooper 1995 V6 model


You can get the check engine light codes yourself on 1985-94 Isuzu vehicles by using a jumper wire between terminal pins 1 and 3 or A and B in the diagnostic connector. This diagnostic connector can be located anywhere from the driver side kick panel, passenger kick panel and sometimes at the center console. When using A and B terminal pins, getting the codes is similar to GM vehicles. Once the jumper wire is connected, turn your key on and read the codes being flashed in the dash panel.


11_2_2012_5_38_56_pm.jpg

Nov 02, 2012 | Cars & Trucks

1 Answer

Am trying to charge my ac but my ac switch keep blinking and the comprresor dont kick in


You can make your compressor come on manually by putting a jumper
in the wiring connector going to the evaporator. It's the 2 wire plug.
If you foolw the wiring from the compressor,you should be able to
figure out where the wiring is. Just remove the plug and put a jumper wire across the terminals to get the compressor clutch to engage and
make the compressor pump.Good luck.

Mar 28, 2010 | 2002 Toyota Camry

2 Answers

NEED TO REEPROGRAMING A REMOTE CONTROL FOR A MALIBU 1998 HOW '?


1. Make sure ignition is in the OFF position.
2. Locate the Programming Connector in the trunk (center of rear shelf). It is a plastic connector with
two wires leading up to it. The connector is not plugged into anything. You may have to pull back
trim to access the connector.

3. The programming connector should have two terminals. Connect both terminals with a suitable
jumper wire. The Keyless Entry Module will lock then unlock all the door lock motors once. Make
sure the terminals remain connected throughout the programming procedure.

4. Press and hold the LOCK and UNLOCK buttons on the transmitter simultaneously for at least 15
seconds or until the vehicle automatically locks and unlocks the door locks. Your new remote has
been accepted and all existing remote codes have been erased.

5. Repeat the previous step for each transmitter to be programmed. Do not remove jumper wire in
between programming of transmitters.

6. Remove the jumper wire from the Keyless Programming Connector.

Dec 15, 2009 | 1998 Chevrolet Malibu

2 Answers

How do i check the codes on a 1993 s10 blazer 4.3


if you go to the auto parts store, they may sell a key that jumps out the dlc connector under the dash. the light will blink for the code.#

Aug 12, 2009 | 1993 Chevrolet S-10

1 Answer

1994 Honda Accord: Need to pull trouble codes


stick a peace of wire in the connector, make sure each end is inside the connector. once you do that you may have to count the blinking light

Feb 28, 2009 | 1994 Honda Accord

1 Answer

Install after market stereo in 2002 malibu ls security shutdowns


yes you have to get a GM pass lock harness the security, door chime, and a few other systems are run through the radio. the harness you need cost about $120 at your local car audio store.

Dec 29, 2008 | 2002 Chevrolet Malibu

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...