Question about 2007 Pontiac Torrent AWD

Open Question

Replacing brake light bulbs on a 2008 torrent

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: How do you replace the brake lights?

Open the hatch and look at the back of the brake light assembly, you will see 2 plastic disks with a little slot in the bottom, insert a flat screwdriver into the slots and pop these disks off, they pop off easily Under the disks are phillips head screws, remove both screws Now, you can't see them, but there are 2 pins built into the brake light assembly which extend into sockets in the body of the car, to remove the assembly, wiggle the entire assembly and push outward TO THE SIDE, NOT toward you, this will wiggle the pins free and the entire assembly will come free once the assembly is free you will see 3 plugs, the top 2 are the brake light bulbs, twist the plugs 1/4 turn and pull them out, now you can see the bulbs, just pull them out and replace them

Posted on Jan 09, 2010

Ad
  • 208 Answers

SOURCE: focus brake light fault

Is this the same light for the emergency brake?

Posted on Aug 02, 2008

ghost4548
  • 776 Answers

SOURCE: how to remove brake bulbs

There are three mounting nuts on each lens assy which are accessed from the trunk behind the liner.

e5045b4.jpg

Posted on May 28, 2009

  • 3600 Answers

SOURCE: How do I change brake light bulb of Nissan Sentra 2008

the llight assembly has to be removed there are 4 screws to get it out with, however some just unscrew counter clockwise to get the bulb out.

Posted on Jun 21, 2009

  • 645 Answers

SOURCE: I have a 2008 Hyundai Accent and none of my brake

check your brake light switch on the brake pedal. See if it has power. Check one side for poer and the other for power while applying the brakes. If it has power its most likely the turn signal switch Brake lights also go thru that switch.

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced the head lamp bulb but only works on high beam


Make sure the other filament is good and that it is receiving power. If no power check relays, fuses, switches,etc for low beams.

Mar 31, 2016 | 2008 Pontiac Torrent

2 Answers

08 jeep liberty has no brake lights all other lights ok, fuse -bulbs ok


Try replacing the brake light switch on your motor . It should be near the brake pedal .

Feb 07, 2015 | 2008 Jeep Liberty

1 Answer

My left brake light and brake light over the tailgate stopped working on my 2008 Aspen. I replaced the bulb on the light over the tailgate and it works fine now. However, I also replaced the bulb on the...


Sometimes the wiring will go bad in the light assembly check all fuses under dash and under hood. sometimes have individual fuses for each tail light. otherwise check wiring.

Jun 28, 2012 | 2008 Chrysler Aspen

1 Answer

Have a Brake light out on my Pontaic Torrent and changed the bulb but still nothing , changed the fuse, and still nothing. what can it be?


The bulb socket could be defective, test it with a DC voltmeter. Make sure you have 12 volts and a good chassis ground.

Jun 13, 2012 | 2008 Pontiac Torrent

1 Answer

2008 torrent brake lights not working


Hello! Four items are involved; #1...Fuse BATT1-57 (50A).#2..Stop Lamp Fuse-27 (15A)... #3..The Stop Lamp Relay..And the Brake positioning sensor....Fuses and Relay located in the under hood box...If the fuses are all good...While someone depressed the brake pedal...Listen to the relay...you can hear it "click"...If it does not pull..Then were down to two components..The relay and the Positioning sensor...Lets eliminate the relay first...Switch it with the Park Lamp Relay (same box, same type relay...If the fault remains the fault is the Brake Positioning Sensor...Guru...saailer

Jan 01, 2012 | 2008 Pontiac Torrent

1 Answer

When I press the brake pedal only the left brake light comes on. The bulbs are good and the fuses are all good. Replace the right light modual but still no help. this is on a 2008 Dodge Nitro


How do you know the bulb is good? Even if it uses the same bulb as the tail light it is always a different filiment. But if you tried replacing the bulb and the fuse than it has to be the wiring. If it's a 2008 it should be covered by the warranty, I would bring it into the dealer.

Aug 17, 2011 | 2008 Dodge Nitro

2 Answers

Right brake light does not work when press the pedal but all 3 bulbs light up when locking or unlocking car so to me bulbs are good is this a fuse?


If it were a fuse issue, neither brake light would work.

The alarm may be connected to running lights and not the brake light, I'd simply swap bulbs lft to right, if the problem follows, new bulbs before worrying about chasing wiring problems.

Hope this helps.

Feb 18, 2011 | 2006 Pontiac Torrent

1 Answer

I have 2008 yukon. i have replaced 7 headlamps


Check the plug ins. Than check the light bulbs and see if they are melted If that is the case than you have to find the bad wires eather way it has something to do with your wires

Apr 20, 2010 | 2001 GMC Yukon Denali

2 Answers

How do you replace the brake lights?


Open the hatch and look at the back of the brake light assembly, you will see 2 plastic disks with a little slot in the bottom, insert a flat screwdriver into the slots and pop these disks off, they pop off easily Under the disks are phillips head screws, remove both screws Now, you can't see them, but there are 2 pins built into the brake light assembly which extend into sockets in the body of the car, to remove the assembly, wiggle the entire assembly and push outward TO THE SIDE, NOT toward you, this will wiggle the pins free and the entire assembly will come free once the assembly is free you will see 3 plugs, the top 2 are the brake light bulbs, twist the plugs 1/4 turn and pull them out, now you can see the bulbs, just pull them out and replace them

Jul 02, 2009 | 2006 Pontiac Torrent

1 Answer

Brake light, 2008 Nissan Sentra


Open the trunk and locate the trim door that covers the back of the drivers side tail light assembly. Open the door and locate the bulb holder. The bulb holder can be removed from the tail light assembly housing by turning counter clockwise 1/4 turn. Holding the bulb holder in one hand, press gently on the bulb and turn then bulb counter clockwise to remove. Replace with a combo bulb and reverse proceedure to re-install.

Jun 21, 2009 | 2008 Nissan Sentra

Not finding what you are looking for?
2007 Pontiac Torrent AWD Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...