Question about 2003 Toyota Tacoma

1 Answer

How do I change my dash lights in my 2003 Tacoma

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

If it is like my 99 taco that i had then remove the bezel ,2 or 3 screws on top under side of dash pad and pull it out gently. i think there are some clips at the bottom. then there are about 4 screws holding the instrument cluster in the dash. remove them and pull out cluster. bulbs are on the back side . just quarter turn . hope this helps.

Posted on Aug 30, 2010

  • 2 more comments 
  • rageagtm Nov 22, 2010

    did you have to remove the steering column?

  • G Gross
    G Gross Nov 22, 2010

    NO, mine had tilt and i just lowered it down using the tilt

  • chris Jun 10, 2013

    if its a 08 tacoma, I pulled it all apart and there is maybe 4 black knobs it looks like but they wont turn i think theyre connected to a mother board

  • chris Oct 05, 2013

    In my 08 tacoma trd i took out the besel and i see 3 black knobs but i believe these are for speedometer and rmps am i correct

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Check engine light remains on. Checked gas cap and fuel tank is full. Changed air filter. Please advise


check engine lights also refer to transmission problems , over heating
best answer is to have the fault codes read to determine if a sensor failure or a real expensive problem

May 18, 2016 | 2003 Toyota Tacoma

1 Answer

How do I replace the bulb behind my fan speed switch for a 2003 Tacoma?


You must remove the dash control to access the bulb.

Feb 26, 2015 | 2003 Toyota Tacoma

1 Answer

Dash lights not working after installation of after market radio


check these fuses then look at the dash connectors see if tight..

Dec 29, 2013 | 2003 Toyota Tacoma

1 Answer

Dash lights dont work


recheck radio wiring for loose connections.

Jul 06, 2010 | 2003 Toyota Tacoma

1 Answer

How do you change dashboard lights in a 2003 toyota tacoma


You need to remove the instrument cluster assembly. You have to remove the cover on the steering column, and then the fascia, in front of the cluster. Next, remove the 4 screws that holds the cluster to the dash. Pull the cluster out, and remove the witing connectors. The bulbs are accessible from the back of the cluster. The bulb replacement can not be done 'from under the dash'.

Nov 21, 2009 | 2003 Toyota Tacoma

1 Answer

Dashboard light out


Hi,

under the drivers side dash board, and under the hood on the drivers side right behind the battery.

Thanks for using "Fixya".

May 28, 2009 | 2003 Toyota Tacoma

1 Answer

2003 parking bulb toyota tacoma


OK, I just fixed mine. The unit pulls out. You have to get a screwdiriver, wrap it with a cloth so it doesn't scratch the paint, then gently wedge the entire unit out. When it pops out, you'll see the clips that keep it in place. You might think its breaking when you pull it out, but trust me this is how you do. Just be gentle with it. After you get the unit out, simply take the socket out and replace the bulb. I did it in five minutes.

Jan 04, 2009 | 2003 Toyota Tacoma

1 Answer

Check engine light on 2003 tacoma


The diagnostic terminal is under the dash, on the driver side. It is white, and sort of oblong, with 2 rows of femal pins. It is NOT recommended to start probing in this connector to "get a code". You may damage the ECU by probing the pins. There is no proceedure to extract DTC by using probes. You need a scan tool.

Aug 26, 2008 | 2003 Toyota Tacoma

Not finding what you are looking for?
2003 Toyota Tacoma Logo

1,234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...