Question about 2007 Honda Accord Sedan

Open Question

Remove a 2007 honda accord exterior door handle

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 43 Answers

SOURCE: Need to know how to install exterior door handles

I'm assuming that you have the coupe not convertible since I've had same problem with my 97 Dodge Avenger and this is quite common from what I have heard. The handle is held in place by two 10mm bolts. One is easily accessable, located right beside the handle with the door open. The other is a little harder to get at. The first thing you need to do is remove the inside door cover, held in place by four screws and push in clips along the bottom that pull out easily. Two of the screws are visible and in the top corners of the door panel. One screw is located behind the inside handle and once removed the moulding comes off quite easily. The other screw is in the hand hold where you pull the door closed and has a small plastic cover over it. If you have power windows you are able to disconnect the switches once the panel is off. If manual windows, the handles are usually held on by a clip that can be pushed off with a screw driver allowing you to pull of the crank handle. The window needs to be in the closed position so you can access the ONE 10mm bolt holding the outer door handle. Once the interior door panel is off, if any clips remain in the door, take them out and put them where they should be in the door cover it won't go back together properly if you don't. Now you'll need to pull down the corner of the plastic covering the door, don't remove all the plastic just enough to allow access to the bolt. I used a small rachet to get it out. It is in a stupid spot with not much room but is doable. Once out, the handle is only being held by the lock rods to the handle and lock cylinder. The lock cylinder is held by a retaining clip which can be slid off allowing the cylinder to be pushed out. The other rod connected to the handle has a plastic clip on it holding it in place. This can be opened with a small screwdriver. Once opened the rod will come out easily and the handle should come off the door. The only problem reinstalling, that I had, was reconnecting the rod to the handle and found that if you unscrew the door latch, the whole mechanism can be moved down, giving you more freedom to work with the rod. You might want to do this before fighting with the clip holding the rod in place, just a thought as I got mine apart in 20 min. Installing the new handle is quite easy, just attach rod to the handle FIRST before anything else. Once the handle is back on the door the lock cylinder can be pushed back in, it just gets in the way if you put it in the handle right away. Hope this is of some help.

Posted on Oct 05, 2008

Ad
  • 58 Answers

SOURCE: 2000 ford explorer door handle

I assume you mean the drivers door. You need to remove the door panel and there are two nuts on the inside holding it on.The door panel has three retaining screws and you need to locate and remove. You then slide the door panel up and then remove it.DON'T pry the panel out you will break it.One screw is on the bottom of the panel. You should see that one. The other ones are under the door switch area and the inside door handle trim.Some have one under the remote mirror trim but not likely.That should give you access to the door handle nuts. Good Luck and I hope this helps you. Thanks Dan

Posted on Jun 21, 2008

  • 840 Answers

SOURCE: removal of door pad on honda jazz 2006 year model

door pad removal look for little pop outs take the pop outs off and thenremove screw then remove the mirror cover then pull on the bottom of door then pull on the side and then pull off trim up and out then you will see a vapor barrier remove it then you see the inside handlejust acouple of srews /please rate my response thank you very much

Posted on Jan 31, 2009

  • 112 Answers

SOURCE: 2002 Nissan Altima Exterior Door Handle

Look at the inside of the door directly behind the door handle. There should be a hole about 15 mm wide.
Just enough to get a small socket through.
Make sure the window is up.

Posted on Feb 03, 2009

  • 5 Answers

SOURCE: driver door handle will not open door 1993 Honda Civic

there is a pin in the door handle might have broke off there are two 10 mm nuts that will release the handle but you have to take the door panels off and remove it any local junk yard should have it or can order it for you

Posted on Mar 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove exterior door handle on a 2007 honda accord. And the door handle broke and it has the child lock on and i cant the door open.


You will either have to reach in through the broken parts with some needle nose pliers to open it. OR remove the door panel from inside the car to pull the proper lever to do so. Removing the door panel with th door closed can be very difficult to do without breaking it I suggest leaving it to a proffessional.

May 26, 2014 | Honda Accord Cars & Trucks

2 Answers

Extirier door handle broke and has child lock on


You may be able to release the door by putting the window down and unlock. then us a screwdriver to press down on the latch release shown red circle in diagram attacked. 3e51e720-3073-4d93-8f31-498f9e0cc85d.png
Here's a video of handle replacement for an earlier model, but should be close to the 2007. https://www.youtube.com/watch?v=bUV6BZfVxDY A owners manual can be found online at 31SDA6421 Unlinked 2007 Accord 4 Door download page 78 talks about the child-proof lock. parts ilistration can be found at Honda site Honda online store 2007 accord rear door locks outer handle parts

Also video producer also sells parts for Hondas.

May 26, 2014 | Honda Cars & Trucks

1 Answer

How to tighten passenger side exterior door handle on a 2007 honda accord sedan


There should be retainer nuts on the inside. You would have to remove the inner door panel to access.

Jun 30, 2013 | 2007 Honda Accord Sedan

1 Answer

Exterior, rear, passenger door handle will not open door. Handle feels loose, as though it is detached from any linkage?


you will need to remove the panel, usually for screws located on arm rest,door handle and sometimes around the middle of the panel behind a round plastic cover. Once all the screws are out the panel pops off, you will need to disconnect the power switches from the inside. Then look at the inside of the door, there is a retaining clip that holds the lever inside the door handle it may have fallen off or the handle cracked. Hope this helped tim

Sep 06, 2010 | 1999 Honda Accord

1 Answer

Take apart honda accord drivers side door


inside the handle there is ONE screw covered by a piece of plastic. remove the plastic and then remove the screw. pull handle out and disconnect it from the door latch bar. replace in reverse

Sep 17, 2009 | 1997 Honda Accord

1 Answer

93 exterior rear door handle replacement


You probably won't get it off from outside. The two bolts go from inside out I believe.

May 15, 2009 | 1993 Honda Civic 4 Door

1 Answer

Replace left front door outside handle pot metal tip broke off


SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Exterior Front Door Handle Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. NOTE: The tie strap does not need to be reinstalled.
    If equipped, remove the tie strap from the anti-theft guard.
  1. Remove the screws and position the anti-theft guard aside.
  1. Release the clip and disconnect the exterior door handle actuating rod.
88661dd.gif
  1. Remove the anti-theft guard.
  1. Remove the exterior door handle screw.
  1. Remove the exterior handle actuating rod.
  1. Remove the exterior door handle lock cylinder cover.
  1. Remove the exterior door handle.

Apr 25, 2009 | 2001 Ford Escape

1 Answer

Exterior rear door handle on Honda Accord 2001


To Remove Door Panel on 2001 Honda Accord:

A: To remove the plastic piece with the door lock button and door handle connected to it:

1- Remove the screw in the middle located behind a plastic cover button
2- Push (slide) the whole assembly Forward (toward front of car)
Besides the screw, it is held in place by 3 hooks on the backside that hook into holes in the metal door frame
3- Now unhook handle from small metal bar going through door by pushing (toward door) plastic clip (blue?) off of the bar, then the bar will come out of the clip hole, thus releasing the handle.
4- Depress little grey button /bar (purple painted on it)on elec. connector to seperate connector, thus releasing door lock switch

Now the whole assembly (metal handle, door lock switch, and plastic piece) will come off door panel

B: The door is held on by 2-screws, 7-plastic snaps/plugs, and 1-plastic plug.

The screws are located: bottom of hand hold and the other behind the handle, both covered by little covers that have to be pryed off to access the screws.(hint: the screw with the built in spacer goes behind the handle when you are trying to reinstall)
The 7-plastic snaps: 3 across bottom and 2 on each side. Not visible, they are mounted to the inside of the panel.
The 1-plastic plug is visible at the upper front of the panel and is the same color as the surrounding trim


C: Take off the big plastic triangle piece above the door panel and behind the mirror. Pull/pry off. It has 2 snaps holding it on. one near bottom and one near the front.

D: Light lens prys off from bottom. Unscrew (1/4 turn) the light assembly with bulb still intact from backside of panel

E: Remove the Hand-Hold/window switch assembly:

Jan 14, 2009 | 1997 Toyota Camry

1 Answer

Problem with passenger door handle (94-97 Accord)


the assy. that keep therod for openeing the door up is whats wrong worn out needs replacing , yu will have to take panel off to repair though good luck

Aug 03, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2007 Honda Accord Sedan Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...