Question about 2006 Saab 9-7X

Open Question

Where is the tire jack located in this vehicle

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tire changing jack location AND using someone elses jack


The jacks for these vehicles are usually under the hood. They are a hydraulic bottle type jack and the tools to operate it are usually located elsewhere in the vehicle. Your owners manual will tell you where everything is and how to use it. The jacks supplied with these vehicles, however, often don't work due to lack of use. You can use a jack from another vehicle as long as it is meant for a truck and not a car. The jack needs to be placed under the axle casing closest to the wheel you are removing. Range Rovers came from the factory with air suspension and jacking any place other than under the axle may result in an air suspension fault. Your vehicle may have been converted to coil springs, but still should be raised under the axle. Just make sure that the part of the jack that contacts the axle cradles it in some way. The factory jacks have a "V" shaped contact point so that the axle will not slide off of the jack while it is in the air. Your best bet is to loosen the lug nuts on the tire you are changing before you jack it up and wait until the vehicle is back on the ground to give the nuts the final tightening. The lug nut size is 1-1/16".

Apr 21, 2014 | 1998 Land Rover Range Rover

Tip

Removing a flat tire on the road safe and easy


Greetings folks,
I have many years experience in the automotive industry and have just about been through every type of situation there is to have experienced.
One simple thing that strikes me as strange is the fact that it is very hard to find proper training for vehicle owners and drivers on the facts about how to change a flat tire, or how to be prepared for a flat tire without even taking the tire off your car or SUV.
How about the trouble you may have had in the past, you knowing exactly how to change a flat but couldn't get the lug nuts off the wheel studs due to someone once before inspecting the brakes or replacing the tires and using an impact gun to install the lug nuts and over tightening them.
Has anyone ever illustrated to you folks the do'e and dont's of using a jack to raise your vehicle off the ground to gain access for removal of a wheel?
Ok lets start with the needed required tools one should carry in their car to prepare for such an event, first lets have a small first aid safety kit for any cuts and bruises including bandades and infection preventing creams and liquids(Iodine, hydrogen peroxide, etc.), next we need to be sure we have a good spare tire in the trunk, easy to check push the side to see if it is hard to the touch indicating it has proper air inflation, also check for a good working tire jack the typical scissor jack and crank handle, which comes with the vehicle make sure it is good, but I prefer to purchase a $29.99 miniature sized professional looking hydraulic floor jack, they fit under the car excellently and work tremendously easy and safe, they can be purchased in Sears Auto or any Auto Parts Store, also a pair of jack stands, two small wedges of wood shaped like large door stops(we will refer to them as the wedges), they can be bought or easily trimmed by a wood worker, from a 4"x4" wood post 6" long and cut on a 45 degree angle on one side, a 1/2" drive breaker bar(heavy duty from Sears Auto Tools Dept) or the like, if not a set of 1/2" impact sockets then at least two common tire wheel lug sizes which are 3/4" and 13/16", these type sockets are made tough and can take a work out, a 48 oz. short handled heavy duty hammer, very important at least two cans of fix a flatNow that you have been introduced to an arrangement of neccessary tools and safety equipment to take along with you on a typical road trip in hopes to keep you and your vehicle from paying dissasterous road service fees and tremendous time lose on the road due to a flat tire, lets get started;Ok now if you experience a flat and notice (once you pull safely all the way over off to the shoulder of the road with your hazard flashers on) that the tire is losing air but doesn't really look in real bad shape, such as a condition tire folks call"run flat" which means the tire has been driving and supporting the vehicles weight with no air in it for a sustained distance, and the tire very noticably has damage all over its sides, etc., this is a typical flat tire that needs to come off, however if the tire appears rather good except for the fact it has or is losing air, get your fix a flat and safety googles out of the trunk with your light duty gloves, find the little black or chrome tire air valve located on the tire near the metal wheels edge, unscrew the little cap, read the directions on the fix a flat can, and install the contents according to the directions.In all cases of this being used they require you to put the screw cap back on the valve and cautiously take your car back onto the road, stay in the right lane with your warniog hazard flashers on and allow the foamy liquid to perform its chemical majic as you drive at the recommended speed on the directions.This should fix your flat without any fuss or muss, have the tire looked at at your next convience to be sure it is ok to drive on it any further.That was relatively easy and thank godness for Fix A Flat, the next type of flat tire however requires a bit more thought and work.I am going to cover first the proper way to jack up your vehicle in the event the tire has to come off for the spare to be installed.

First, spull to safety, put your hazard flashers on whether its day or night, look for an area that the ground looks pretty level.

Secondly, open your trunk and leave it open, remove your spare tire and all the neccessary tools you will need to change the tire.

Third, using your breaker bar and the proper impact socket attempt to loosen(but dont remove) the tire nuts on the flat tire, if a tire lug wont come loose, getb the 48 oz. hammer and the impact socket that fits the wheel lug and hit it with a sharp firm blow, be certain you have on the eye protection as hitting steel against steel can cause some steel fragments to fly you don't want your eye to be the reciever of such, after you hit it the nut should turn loose, remeber you are only turning them about 1/2 turn loose you don't remove them until the tire is jacked up and off the ground(doing this helps prevent the car from falling off the jack had you jacked it first then applied all sorts of tugging etc on the tight lug nuts).

Fourth, place the wedges in front of and behind one of the tires on the opposite side of the car, this will eliminate the possibility of the car sliding forward or backwards off the jack once it is jacked up.
Find a secure flat firm welded frame area to place the floor jack under, or if using the original scissor jack be sure you are also using it in a firm jacking location(most scissor jacks have a notch put in the under side of the vehicle that allows the jack to fit into the channel securely) once found and level jack the car's tire off the ground, install the jack stands under the vehicle in a firm body frame sort of area to prevent the car from falling off the jack you can never be too safe.

Fifth, install the spare tire on the vehicle and while it is on the jack, start threading the wheel lug nuts onto the appropriate wheel studs, use your wrench and socket to get the nuts down only slightly tight.

Sixth, remove the jack stand or stands depending on how secure you felt about using one or two, lower the jack, once the tire is firmly touching the ground, continue to tighten the remaining wheel lug nuts one at a time until they feel good and firmly tight.

Seventh, remove the wedges from the wedged tire on the other side of the vehicle, remove the jack, put everything back into the trunk including the flat tire. Happy Motoring!!!

on Jun 08, 2010 | Chevrolet Camaro Cars & Trucks

1 Answer

Placement of jack to change the front driver side tire


There is a notch location just about below front fender. It is a gap in the downward protruding flange that will be the size of the top of the jack. Set parking brake and chock or block rear wheels if possible to prevent vehicle moving and avoid injury.

Jan 07, 2014 | 1994 Buick Roadmaster

1 Answer

Changing rear flat tire


Find jack follow instructions to raise vehicle after parking brake is on. Remove lug nuts and take wheel with flat tire off. Replace with the spare tire and tighten lug nuts. lower vehicle, put jack , lug wrench and flat tire in vehicle. Drive to a tire repair store and fix the problem.

Dec 11, 2010 | 1996 Dodge Caravan

2 Answers

Where is the spare tire located on a 1995 ford aerostar?


Section 00-02: Lifting, Jacking and Spare Tire Stowage 1995 Aerostar, Ranger, Explorer Workshop Manual
TIRE STOWAGE Tire, Spare, Removal, Aerostar If the Aerostar is a standard length vehicle the spare tire is mounted inside to a carrier at the left rear quarter panel. To remove the spare tire, remove the wing nut and plate. A flat tire can be temporarily stowed in the same location.



If the Aerostar is the bus with a standard length body or extended length (all models), the temporary spare tire is stowed at the rear of the vehicle under the body. The Aerostar standard length E-4WD bus spare tire is mounted on the floor.
  1. Insert lug nut wrench into the actuator hole and turn counterclockwise until the cable extends to allow the spare tire to be pulled rearward from under the vehicle.
  1. Slide spare tire to the rear and remove the retainer from the wheel.
  1. To stow cable/retainer with spare tire removed, insert cable fitting into carrier rear wall slot, place wheel retainer against the carrier, and turn lug nut wrench clockwise until slack is removed.
please rate, thanks

Jul 09, 2010 | 1995 Ford Aerostar

1 Answer

Where is the horn located


For Horn on 1995 Dodge Neon
  1. Loosen the lug nuts on the front tire on the driver's side of the car.
  2. Jack up the vehicle, making sure it's high enough to clear the jack stands.
  3. Securely place the jack stands under the vehicle.
  4. Remove the tire from the car, and, if necessary, remove the inner wheel lining to allow access to the horn.
  5. Locate the horn and wiring, which should be located inside the front bumper of the car, slightly above the area of the tire.
Hope this help (remember comment and rated this).

Apr 09, 2010 | 1995 Dodge Neon

1 Answer

Where can i put jack stands to do an oil change?


There are (2) three and a half inch long jack pads on both sides of your vehicle along the frame rail located exactly twelve inches behind each of your front wheel assemblies. You can place your jack stands safely there. Your oil filter is located on the passenger side of the vehicle, so you'll need to remove the oil filter by accessing it right above the lower control arm using a three-pronged oil filter wrench and a 9" extension with a ratchet.

IMPORTANT! : Always replace the oil drain plug gasket with each lube, oil and filter service. (it looks like a copper or aluminum washer)

P.S. - Don't forget to adjust your tire pressures to 30 p.s.i. in accordance with the tire placard located in the driver side doorjamb.

Dec 15, 2009 | 2007 Suzuki Forenza Sedan

1 Answer

Cant release spare tire from under car of 2002 mercury villager. no owners manual available.


Location of the spare tire and tools
The spare tire and tools for your vehicle are stowed in the following
locations:
Item Location
Spare tire Under the vehicle, just forward of
the rear bumper
Jack assembly Under the third row bench seat in
the tool bag
Removing the jack and tools
1. Lift the 3rd row seat cushion.
2. Remove the jack assembly from the bag under the seat.

Removing the spare tire
1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up
the piece of carpet to expose the hex nut.
2. Insert the lug nut wrench on the
hex nut in cargo floor.
3. Turn the wrench
counterclockwise until tire is
lowered to the ground and the cable
is slightly slack.
4. Remove the retainer from the
spare tire. It may be necessary to
lift one end of the tire to disengage
the retainer

Jul 12, 2009 | 2002 Mercury Villager

2 Answers

How to change the tire


First off did you Know this ?????

Make / Models : Model/Build Years:
GMC / 1500 2004
Regency / Chevrolet 1500 2004
MANUFACTURER: General Motors Corp.
NHTSA CAMPAIGN ID Number : 04V240000 Recall Date : MAY 14, 2004
COMPONENT: Tires: Temporary/Emergency Spare Tire
Potential Number Of Units Affected : 285
SUMMARY:
The spare tire and wheel assembly that was provided on certain conversion vehicles will not fit on the front wheel hub due to offset of the wheel. However, it will fit on the rear wheels.
CONSEQUENCE:
If someone has a flat tire on the front wheel, they will not be able to install the provided spare tire.
REMEDY:
Dealers will install a spare wheel with the correct offset. Owner notification began on June 11, 2004. Owners should contact Regency at 1-800-989-4727.
NOTES:
Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236)

SPARE TIRE is Under rear of truck use Long Cranking in HoleClose to Lisence Plate to Lower it Down Cranking Counter Clockwise. Wing in center of Wheel pokes thrugh Hole in Center of wheel
Reverse Procedure to Put old tire in Tire Storage Compartment

  1. Locate Jack & Wheel Lug Nut Wrench
  2. There is Directions as to where to placse the Jack for raising Truck Where Jack is Located
  3. Set Park Brake Chalk tire if possible & Hazard lights (If on the Roadside)
  4. Loosen all Wheel Nuts on said wheel before Raising Vehicle
  5. Place Jack In Recomended Placment spot
  6. Rear is Normaly on Axel close to Shock
  7. Front is Normaly on FRAMERAIL
  8. Raise vehicle untill tire is 3-4 inches off ground as Flat will Lower vehicle
  9. Remove All Wheel Nuts And Wheel
  10. Place new wheel/tire on Vehicle and start all nuts
  11. Tighten nuts as tight as Possible then Lower Vehicle Untill tire touches ground Good
  12. Now Toque Wheel Nuts as tight as Possible with hand tool
  13. Lower vehicle all the way down
  14. Put away tools and Reliece Park Brake
  15. Torque should be around 100-130 foot Pounds

I Hope this is What You Wanted Its Off the Cuff as My Reference Books done have this Procedure.


Jan 26, 2009 | 2004 GMC Sierra

1 Answer

A friend is broke down with another friends truck with a flat tire and needs to know where to find the tire jack


Jack should be either located under hood mounted to fender well or in a side compartment inside of the car behind the rear wheelwell or even under the carpet in the trunk where the spare tire sohuld be located. If it is not in those locations then chances are that someone has removed them from the vehicle

Jan 03, 2009 | Ford Fairmont Cars & Trucks

Not finding what you are looking for?
2006 Saab 9-7X Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...