Question about 1992 Chevrolet Lumina
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
itsalmos identical location of the '93 Lumina it's almost dead center of the underneath of the car. It is a rather simple change out.
first spray the nut with WD40, then holding one side firm just unloosen the other side. Be careful under a little bit of pressure and fuel will come out. Next you have to remove the cover thing on the other side by sliding it back. Push down on those two tabs and pull, should come right apart. Hope this helps.
Best regards Mike
Posted on Feb 14, 2010
the easy way is to remove the three screws at the filler neck then look under truck at backside of filler neck and remove the one bolt holding ground strap then go to rear drivers side and unhook the wire harness for the rear lights simple just one connector for lights then there is a ground wire right at the connector you just unhooked bolted to frame rail remove it on the frame along both sides you will find 4 17mm or 18mm bolts remove all 8 bolts have some friends grab bed on both sides pick up bed and walk backwards one or two feet let area in front of wheels sit on rear tire area behind wheels will sit on bumper look down right behind cab on drivers side and you will see the fuel pump in top of tank i know this sounds like a lot but believe me it,s easier than lowering that tank and having to undo lines and what not laying on ground under truck you will be able to service pump standing up in good light conditions
Posted on Apr 26, 2010
Follow the steps care fully
Open the hood and relieve the fuel system pressure. On the fuel rail, right before the first fuel injector, locate the Schrader valve-similar to a tire air valve-on the inlet fuel line. Using a small screwdriver, depress the stem inside the valve while covering the valve with a shop rag to catch the squirt of fuel.
Raise the back of the vehicle using a floor jack and support it safely on jack stands.
Locate the fuel filter along the frame rail-passenger side-of the vehicle, near the fuel tank.
Unplug the quick-connect fuel inlet line on the back of the filter by pressing the lock tabs. Push the connector towards the filter and then pull to disconnect the fuel supply line.
Disconnect the outlet fuel line from the filter-the line going toward the engine-by using a backup wrench to hold the line nut while disconnecting the lock nut on the filter with a tube wrench.
Remove the filter from its mounting bracket and install the new filter in place, making sure the arrow on the side of the filter case points toward the engine.
Install the outlet fuel line. Tight the lock nut finger tight, then hold the fuel line nut with the backup wrench and tight the lock nut with the tube wrench. Make sure not to over tighten the nut to prevent fuel leaks.
Press the fuel supply line fitting against the small tube at the back of the filter until the lock tabs snap in place.
Lower the vehicle, start the engine and check for leaks.
Posted on Oct 20, 2010
Tips for a great answer:
Apr 26, 2012 | 1997 Chevrolet Astro
Feb 26, 2011 | 1992 Chevrolet Lumina
Dec 12, 2009 | 1992 Chevrolet Lumina
Oct 28, 2009 | 1992 Chevrolet Lumina
Sep 18, 2009 | 1992 Chevrolet Lumina
Feb 20, 2009 | 1995 Chevrolet Lumina Apv
Feb 03, 2009 | 1993 Chevrolet Lumina
Jan 30, 2009 | 1997 Chevrolet Lumina
Jun 14, 2017 | 1992 Chevrolet Lumina
66 people viewed this question
Usually answered in minutes!