Question about Kia Spectra

Open Question

Torque specs for axle nut for 2003 kia spectra need asap

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

  • 312 Answers

SOURCE: 2008 Impala axle shaft torque spec

118 ft lbs

Posted on Jan 11, 2010

  • 117 Answers

SOURCE: I need the torque specs

The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Posted on Jan 29, 2011

zappanut
  • 959 Answers

SOURCE: need torque specs on axle nuts for dana 50 rear

Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Posted on Feb 19, 2011

sammiamm9p
  • 41 Answers

SOURCE: Need valve cover torque specs for 2002 Kia Spectra

The torque specs for a Kia 1.8 valve cover is 43-78 inch pounds...... Basically just snug....

Posted on Nov 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs. for a 2006 kia rio5 front wheel bearing?


Product Note: Wheel Bearing -- Wheel Bearing; Axle Nut Torque Spec: 188 ft-lbs / 255Nm.

Oct 02, 2015 | Kia Cars & Trucks

1 Answer

What is the torque spec for the front center axle nut on a 2003 tahoe?


The torque specs.are for 15k series trucks is 155 ft.lbs.For 25/35 series it`s 133 ft.lbs.Hope this helps.Good luck.

Dec 03, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

Need valve cover torque specs for 2002 Kia Spectra


The torque specs for a Kia 1.8 valve cover is 43-78 inch pounds...... Basically just snug....

Nov 13, 2011 | Cars & Trucks

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

How to remove cv drive shaft on 03 kia spectra


jack up the vehicle on the frame or on the body lip not on the front suspension take the lower ball joint loose and remove the axle nut and push the axle out of the knuckle and tie the knuckle up out of the way then you can take a pry bar and pry the axle out of the transmission being careful not to damage the seal. then reinstall new axle in reverse order

Nov 08, 2009 | 2003 Kia Spectra

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Need torque spec for axle nut 2003 lancer


THE BIG NUT DONT TORK IT SHOULD HAVE HAD A CARTER PIN IN IT THAT KEEPS IT FROM BACKING OFF BUT U JUST SNUG IT UP TIGHT THIN TURN 1/2 TURN PUT CARTER PIN IN THE HOLE IF U TIGHTING THIS NUT REAL TIGHT THE BEARING WILL GET HOT AND LOCK UP ON U GOOD LUCK PLEASE RATE THIS

Apr 05, 2009 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...